Mitsubishi Evolution X. Manual — part 636
SEAT ASSEMBLY
TSB Revision
INTERIOR
52A-21
REMOVAL SERVICE POINT
.
<<A>> WIRING HARNESS CONNECTOR DISCON-
NECTION
AC709108
D-32
D-31
AB
D-36
D-26
D-34
D-37
D-38
D-39
D-41
D-33
Disconnect the following wiring harness connectors:
Connector number Connector name
D-26 (2
− yellow)
Side impact sensor connector (LH)
D-31 (4
− black)
Heated seat assembly connector
(LH) <Vehicle with heated seat>
D-32 (2
− gray)
Seat slide sensor connector
(Driver's seat)
D-33 (4
− black)
Seat belt switch connector (Driver's
seat)
D-34 (2
− yellow)
Side airbag module (squib)
connector (LH) <Vehicles with side
airbag>
D-36 (2
− yellow)
Side airbag module (squib)
connector (RH) <Vehicles with side
airbag>
D-37 (2
− black)
Seat belt switch connector
(Passenger's seat)
D-38 (4
− black)
Heated seat assembly connector
(RH) <Vehicle with heated seat>
D-39 (6)
Front seat assembly connector
(RH)
D-41 (2
− yellow)
Side impact sensor (RH) connector
NOTE:
AC706606
AE
Locking button
Side-airbag module
connector
When disconnecting the side air bag module connec-
tors of D-34 and D-36, unlock the connector by sliding the lock-
ing button to the direction of the arrow as shown in the figure,
and then disconnect the connector.
SEAT ASSEMBLY
TSB Revision
INTERIOR
52A-22
INSTALLATION SERVICE POINT
.
>>A<< FRONT SEAT ASSEMBLY INSTALLATION
AC708437AB
1. Temporarily tighten the bolts in all mounting locations
shown in the illustration with no load applied to the front
seat cushion and check the operation of the seat slide.
2. Tighten the bolts in all mounting locations to the specified
torque.
INSPECTION
M1522005500339
CONTINUITY TEST OF HEATED SEAT SWITCH
.
ACX00625
1. Check for continuity between terminals.
Item
Switch
position
Tester
connection
Specified
condition
Driver's
seat side
HI
1
− 5, 3 − 8
Continuity
exists (2
Ω
or less)
OFF
1
− 5, 3 − 5, 5
− 8
Open
circuit
LO
3
− 5
Continuity
exists (2
Ω
or less)
Front
passenger'
s seat side
HI
4
− 5, 8 − 9
Continuity
exists (2
Ω
or less)
OFF
4
− 5, 5 − 8, 5
− 9
Open
circuit
LO
5
− 9
Continuity
exists (2
Ω
or less)
2. Check that the indicator is lighted at HI or LO when battery
voltage is supplied to terminal 5 and terminal 8 is grounded.
3. Check that indicator is lighted when battery voltage is
supplied to terminals 2 and terminal 6.
.
SEAT ASSEMBLY
TSB Revision
INTERIOR
52A-23
SEAT CUSHION HEATER CHECK
AC701225
Heated seat
assembly
Seatback
heater
AC
Measure the resistance between terminals.
Standard value: At room temperature 20
° C (68 ° F)
Between heated seat assembly terminals 1 and seat-
back heater terminal 1: 3.84
± 4.69 ohms
Between heated seat assembly terminals 2 and seat-
back heater terminal 1: 0.14
± 0.18
.
SEATBACK HEATER CHECK
1
2
AC200100
Measure the resistance between terminals.
Standard value: At room temperature 20
° C (68 ° F)
Between terminals 1 and terminal 2: 5.40
± 6.60 ohms
HEATED SEAT RELAY CONTINUITY CHECK
AC610364
2
3
4
1
AB
Heated seat
relay
Battery voltage Tester
connection
Specified
condition
Not applied
3
− 4
Open circuit
• Connect
terminal 1 to
the positive
battery
terminal
• Connect
terminal 2 to
the negative
battery
terminal
Continuity
exists (2
Ω or
less)
SEAT ASSEMBLY
TSB Revision
INTERIOR
52A-24
DISASSEMBLY AND ASSEMBLY
M1522001501415
AC709596AB
12
16
15
4
5
11
2
13
41 ± 10 N·m
30 ± 8 ft-lb
1
7
10
3
7
6
12
40 ± 4 N·m
30 ± 2 ft-lb
40 ± 4 N·m
30 ± 2 ft-lb
41 ± 10 N·m
30 ± 8 ft-lb
41 ± 10 N·m
30 ± 8 ft-lb
9
10
14
8
Disassembly steps
1. Seat belt harness connector
2. Seat belt inner
3. Seat cushion cover fixation clip
4. Hinge cover
5. Reclining adjuster knob
6. Side shield cover
7. Heated seat & Side air bag harness &
Seat slide sensor connector
8. Front seat assembly harness
connector (Passenger's seat)
9. Front seatback assembly
10. Headrestraint garnish
11. Front seatback
12. Slide rail adjuster mounting bolts
13. Front seat cushion
14. Slide adjuster assembly
15. Front seat slide adjuster lever
16. Slide adjuster
Disassembly steps (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст