Mitsubishi Evolution X. Manual — part 891
MB991897
SPECIAL TOOL
TSB Revision
REAR AXLE
27-25
MB991897 or
MB992011
Ball joint remover
MB991113-01,
MB990635-01 or
General service tool
Self locking nut removal
NOTE: Steering linkage puller
(MB990635 or MB991113)is also
used to disconnect knuckle and tie
rod end ball joint.
MB990850
MB990850
End yoke holder
−
Companion flange fixing
MB990925
A
B
C
MB990925
A: MB990926
−
MB990937
B: MB990938
C: MB990939
Bearing and oil seal
installer set
A: Installer adapter
B: Bar
C: Brass bar
MB990925-01 or
General service tool
Press-fitting of differential carrier oil
seal
(Use together with MB991115)
Tool
Tool number and
name
Supersession
Application
MB991159AB
A
B
SPECIAL TOOL
TSB Revision
REAR AXLE
27-26
MB991159
Bushing remover and
installer
A: MB991162
Bolt
B: MB991218
Bearing
−
Removal of the rear suspension
crossmember bushing
NOTE: When press-fitting the
bushing, use the bearing included in
MB992107.
MB990847
MB990847
Base
−
B992234
MB992234
Bearing
−
B992235
MB992235
Adapter
−
B992253
MB992253
Remover and
installer
−
B992254
MB992254
Base
−
MB990326
MB990326
Preload socket
General service tool
Measurement of the wheel bearing
rotation starting torque
MB990685
Torque wrench
General service tool
Tool
Tool number and
name
Supersession
Application
ON-VEHICLE SERVICE
TSB Revision
REAR AXLE
27-27
MB990925 BEARING AND OIL SEAL INSTALLER SET
Tool
Type
Tool number
O D mm (in)
ACX02372 AE
A
B
C
Remover bar
Installer bar
(Snap-in type)
Toolbox
Installer adapter
A
MB990926
39.0 (1.54)
MB990927
45.0 (1.77)
MB990928
49.5 (1.95)
MB990929
51.0 (2.00)
MB990930
54.0 (2.13)
MB990931
57.0 (2.24)
MB990932
61.0 (2.40)
MB990933
63.5 (2.50)
MB990934
67.5 (2.66)
MB990935
71.5 (2.81)
MB990936
75.5 (2.97)
MB990937
79.0 (3.11)
B
MB990938
−
C
MB990939
−
ON-VEHICLE SERVICE
REAR AXLE TOTAL BACKLASH CHECK
M1271001200456
1. Shift the shift lever to the Neutral position, pull the parking
brake lever, and then raise the vehicle using a jack.
AC705969AB
Mating marks
2. Fully turn the propeller shaft clockwise, and place the mating
marks on the companion flange dust cover and differential
carrier.
AC705969AC
3. Fully turn the propeller shaft counterclockwise, and measure
the travel distance of mating marks.
Limit: 6 mm(0.2 inch)
4. If the backlash exceeds the limit, replace the differential
carrier assembly.
ON-VEHICLE SERVICE
TSB Revision
REAR AXLE
27-28
GEAR OIL LEVEL CHECK
M1271004900090
DIFFERENTIAL MECHANISM PART
AC705198AB
Filler plug
1. Remove the filler plug.
AC102739
6 mm
(0.2 in)
AJ
Upper
limit
Lower
limit
Gear oil
2. Check that the gear oil level is in between the upper limit
(bottom of the oil filler plug hole) and the lower limit.
3. If the gear oil level is not in between the upper limit and the
lower limit, fill the specified gear oil to the bottom of the filler
plug hole.
Specified gear oil: MITSUBISHI Genuine DIA QUEEN
LSD gear oil
4. Install the filler plug, and tighten it to the specified torque.
Tightening torque: 49
± 10 N⋅ m (37 ± 7 ft-lb)
TORQUE TRANSFER MECHANISM PART
AC705199AB
Filler plug
1. Remove the filler plug.
AC102739
6 mm
(0.2 in)
AJ
Upper
limit
Lower
limit
Gear oil
2. Check that the gear oil level is in between the upper limit
(bottom of the oil filler plug hole) and the lower limit.
3. If the gear oil level is not in between the upper limit and the
lower limit, fill the specified gear oil to the bottom of the filler
plug hole.
Specified gear oil: DIAMOND ATF-SP III
4. Install the filler plug, and tighten it to the specified torque.
Tightening torque: 49
± 10 N⋅ m (37 ± 7 ft-lb)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст