Mitsubishi Evolution X. Manual — part 417
DIAGNOSIS <TC-SST>
TSB Revision
TWIN CLUTCH- SPORTRONIC SHIFT TRANSMISSION (TC-SST)
22C-125
LOGIC FLOW CHARTS (Monitor Sequence) <Shift fork 2 current gear: 5th gear>
.
DTC SET CONDITIONS <SHIFT FORK 2
CURRENT GEAR: 5TH GEAR>
Check Conditions
• Voltage of battery: 8 V or more.
• Voltage of battery: 16.5 V or less.
• Engine speed: 500 r/min or more.
• Time since above engine condition: 400 millisec-
ond or more.
• Input shaft 1 (odd) speed: 500 r/min or more.
• Shift fork 2 current gear: 5th gear.
• Synchro (5th gear) slip speed: 80 r/min or more.
• Requested shift fork: Not shift fork 2.
JUDGMENT CRITERIA
• Shift fork 2 position: 6 mm (0.24 inch) or less.
(250 millisecond)
.
OBD-II DRIVE CYCLE PATTERN <SHIFT
FORK 2 CURRENT GEAR: 5TH GEAR>
The travel distance of the shift fork 2 remains 6 mm
(0.24 inch) or more for 250 milliseconds.
.
AC710682
START
No
Good
Malfunction
END
Monitoring condition met
Continuous failure
for 250 msec
No
Yes
Yes
Yes
No
Shift fork position
< 6 mm (0.24 inch)
DIAGNOSIS <TC-SST>
TSB Revision
TWIN CLUTCH- SPORTRONIC SHIFT TRANSMISSION (TC-SST)
22C-126
LOGIC FLOW CHARTS (Monitor Sequence) <Shift fork 2 current gear: 3rd gear>
.
DTC SET CONDITIONS <SHIFT FORK 2
CURRENT GEAR: 3RD GEAR>
Check Conditions
• Voltage of battery: 8 V or more.
• Voltage of battery: 16.5 V or less.
• Engine speed: 500 r/min or more.
• Time since above engine condition: 400 millisec-
ond or more.
• Input shaft 1 (odd) speed: 500 r/min or more.
• Shift fork 2 current gear: 3rd gear.
• Synchro (3rd gear) slip speed: 80 r/min or more.
• Requested shift fork: Not shift fork 2.
JUDGMENT CRITERIA
• Shift fork 2 position: −6 mm (−0.24 inch) or more.
(250 millisecond)
.
OBD-II DRIVE CYCLE PATTERN <SHIFT
FORK 2 CURRENT GEAR: 3RD GEAR>
The travel distance of the shift fork 2 remains
−6 mm
(
−0.24 inch) or less for 250 milliseconds.
.
PROBABLE CAUSES
• Malfunction of TC-SST-ECU
DIAGNOSTIC PROCEDURE
STEP 1. Scan tool CAN bus diagnostics
Using scan tool MB991958, diagnose the CAN bus lines.
Q: Is the check result normal?
YES : Go to Step 2.
NO : Repair the CAN bus lines. (Refer to GROUP 54C
−
Troubleshooting
.) After repairing the CAN
bus line, go to Step 2.
AC710683
START
No
Good
Malfunction
END
Monitoring condition met
Continuous failure
for 250 msec
No
Yes
Yes
Yes
No
Shift fork position
> -6 mm (-0.24 inch)
DIAGNOSIS <TC-SST>
TSB Revision
TWIN CLUTCH- SPORTRONIC SHIFT TRANSMISSION (TC-SST)
22C-127
STEP 2. Check whether the DTC is reset.
Q: Is DTC No. P1829 set?
YES : Replace the TC-SST assembly. (Refer to
NO : Intermittent malfunction. (Refer to GROUP 00
− How
to Cope with Intermittent Malfunction
.)
DTC P182A: Shift Fork Position Sensor 3 System (Voltage low range out)
CAUTION
• If there is any problem in the CAN bus lines,
an incorrect diagnostic trouble code may be
set. Prior to this diagnosis, diagnose the CAN
bus lines.
• Whenever the ECU is replaced, ensure that
the CAN bus lines are normal.
.
DIAGNOSTIC FUNCTION
TC-SST-ECU checks that the voltage of the shift fork
position sensor 3 is normal.
.
DESCRIPTIONS OF MONITOR METHODS
The voltage of the shift fork position sensor 3 is too
low.
.
MONITOR EXECUTION
• Continuous
.
MONITOR EXECUTION CONDITIONS
(OTHER MONITOR AND SENSOR)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• P182B: Shift fork position sensor 3 system (Volt-
age high range out)
• P182C: Shift fork position sensor 3 system (Out-
put range out)
• P182D: Shift fork position sensor 3 system (Neu-
tral)
• P182E: Shift fork position sensor 3 system (Poor
performance)
• P1844: Shift fork 3 malfunction
• P1852: Shift fork 1 or 2 opposite direction move-
ment
• P1855: Shift fork 3 or 4 opposite direction move-
ment
• P1858: Even number gear axle interlock
• P1876: Gear block 1st
• P1877: Gear block 2nd
• P1878: Gear block 3rd
• P1879: Gear block 4th
• P187A: Gear block 5th
• P187B: Gear block 6th
• P187C: Gear block reverse
Sensor (The sensor below is determined to be
normal)
• Not applicable
.
DIAGNOSIS <TC-SST>
TSB Revision
TWIN CLUTCH- SPORTRONIC SHIFT TRANSMISSION (TC-SST)
22C-128
LOGIC FLOW CHARTS (Monitor Sequence)
.
DTC SET CONDITIONS
Check Conditions
• Voltage of battery: 8 V or more.
• Voltage of battery: 16.5 V or less.
JUDGMENT CRITERIA
• Position sensor voltage: 0.128 V or less. (160 mil-
lisecond)
.
OBD-II DRIVE CYCLE PATTERN
The position sensor voltage remains 0.128 V or more
for 160 milliseconds.
.
PROBABLE CAUSES
• Malfunction of TC-SST-ECU
DIAGNOSTIC PROCEDURE
STEP 1. Scan tool CAN bus diagnostics
Using scan tool MB991958, diagnose the CAN bus lines.
Q: Is the check result normal?
YES : Go to Step 2.
NO : Repair the CAN bus lines. (Refer to GROUP 54C
−
Troubleshooting
.) After repairing the CAN
bus line, go to Step 2.
STEP 2. Check whether the DTC is reset.
Q: Is DTC No. P182A set?
YES : Replace the TC-SST assembly. (Refer to
NO : Intermittent malfunction. (Refer to GROUP 00
− How
to Cope with Intermittent Malfunction
.)
AC710676
START
No
Good
Malfunction
END
Monitoring condition met
Continuous failure
for 160 msec
No
Yes
Yes
Yes
No
Shift fork position
< 0.128 V
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст