Mitsubishi Evolution X. Manual — part 223
AC601589 AJ
Special tool - Power plant ECU check harness (MB992110) connector: Component side
48-Pin connector
(ECM connector B-10)
64-Pin connector
(ECM connector B-09)
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-61
Terminal
number
Check item
Check condition
Normal condition
10
TP sensor (main)
• Remove the intake air
hose at the throttle body
• Disconnect the TP sensor,
and then connect
terminals 3, 4, 5 and 6
with the use of the special
tool: MB991658 (Test
harness).
• Ignition switch: "ON"
Fully close the
throttle valve
with your finger
0.3
− 0.7 V
Fully open the
throttle valve
with your finger
4.0 V or more
11
TP sensor (sub)
• Remove the intake air
hose at the throttle body
• Disconnect the TP sensor,
and then connect
terminals 3, 4, 5 and 6
with the use of the special
tool: MB991658 (Test
harness).
• Ignition switch: "ON"
Fully close the
throttle valve
with your finger
4.0 V or more
Fully open the
throttle valve
with your finger
1.0 V or less
12
Power supply voltage
applied to TP sensor
Ignition switch: "ON"
4.9
− 5.1 V
15
TAC motor (+)
• Ignition switch: "ON"
• Accelerator pedal: fully opened to fully
closed
Decreases slightly
(approx. 2 V) from
battery voltage.
16
TAC motor (
−)
• Ignition switch: "ON"
• Accelerator pedal: fully closed to fully
opened
Decreases slightly
(approx. 2 V) from
battery voltage.
74
APP sensor (main)
Ignition
switch:
"ON"
Release the accelerator pedal
0.9
− 1.1 V
Depress the accelerator pedal.
4.0 V or more
75
Power supply voltage
applied to APP
sensor (main)
Ignition switch: "ON"
4.9
− 5.1 V
77
APP sensor (sub)
Ignition
switch:
"ON"
Release the accelerator pedal
0.4
− 0.6 V
Depress the accelerator pedal.
2 V or more
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-62
78
Power supply voltage
applied to APP
sensor (sub)
Ignition switch: "ON"
4.9
− 5.1 V
85
Clutch switch <M/T>
Ignition
switch:
"ON"
Depress the clutch pedal.
1V or less
Release the clutch pedal.
Battery positive
voltage
107
Cruise control switch
power supply
Ignition
switch:
"ON"
All switches: Released
4.7 - 5.0 V
"ON/OFF" switch: Pressed
0 - 0.5 V
"CANCEL" switch: Pressed
1.0 - 1.8 V
"COAST/SET" switch: Pressed
2.3 - 3.0 V
"ACC/RES" switch: Pressed
3.5 - 4.2 V
108
Stoplight switch
(brake switch)
Ignition
switch:
"ON"
Depress the brake pedal.
Battery positive
voltage
Release the brake pedal.
1V or less
Terminal
number
Check item
Check condition
Normal condition
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-63
SPECIAL TOOLS
M1172000600974
Tool
Tool number and name Supersession
Application
MB991910
MB991826
MB991958
MB991911
MB991914
MB991824
MB991827
MB991825
Do not use
a
b
c
d
e
f
g
Do not use
MB991958
a: MB991824
b: MB991827
c: MB991910
d: MB991911
e: MB991914
f: MB991825
g: MB991826
Scan tool (M.U.T.-III sub
assembly)
a: Vehicle
communication
interface (V. C. I.)
b: M.U.T.-III USB cable
c: M.U.T.-III main
harness A (Vehicles
with CAN
communication
system)
d: M.U.T.-III main
harness B (Vehicles
without CAN
communication
system)
e: M.U.T.-III main
harness C (for Daimler
Chrysler models only)
f: M.U.T.-III
measurement adapter
g: M.U.T.-III trigger
harness
MB991824-KIT
NOTE: g: MB991826
M.U.T.-III Trigger
Harness is not
necessary when
pushing V.C.I. ENTER
key.
CAUTION
For vehicles with CAN
communication, use
M.U.T.-III main harness A
to send simulated vehicle
speed. If you connect
M.U.T.-III main harness B
instead, the CAN
communication does not
function correctly.
• Checking DTC.
• Checking data list.
MB991223
a
d
c
b
DO NOT USE
BF
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-64
MB991223
a: MB991219
b: MB991220
c: MB991221
d: MB991222
Harness set
a: Test harness
b: LED harness
c: LED harness adaptor
d: Probe
General service tools
Checking the continuity and
measuring the voltage at the
harness connector
MB992006
MB992006
Extra fine probe
General service tool
Continuity check and voltage
measurement at harness
wire or connector for loose,
corroded or damaged
terminals, or terminals
pushed back in the
connector.
MB992110
MB992110
Power plant ECU check
harness
−
Measuring the terminal
voltage at the ECM
MB991658
MB991658
Test harness
−
Measuring the terminal
voltage at the TP sensor
Tool
Tool number and name Supersession
Application
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст