Mitsubishi Evolution X. Manual — part 1032
HANDS-FREE CELLULAR PHONE SYSTEM
TSB Revision
CHASSIS ELECTRICAL
54A-489
SYMPTOM PROCEDURES
Inspection Procedure 1: Hands free cellular phone system does not work normally.
CAUTION
Before replacing the ECU, ensure that the power supply circuit, the ground circuit and the communi-
cation circuit are normal.
Hands Free Module Power Supply Circuit
FUSIBLE
LINK
36
HANDS FREE
MODULE
RELAY BOX
ENGINE
COMPARTMENT
HANDS-FREE CELLULAR PHONE SYSTEM
TSB Revision
CHASSIS ELECTRICAL
54A-490
Hands Free Cellular Phone System Circuit
MICROPHONE
UNIT
HANDS
FREE
MODULE
RADIO AND CD PLAYER
MULTIVISION
DISPLAY
<VEHICLES WITH
MITSUBISHI
MULTI-COMMUNICATION
SYSTEM (MMCS)>
<VEHICLES WITHOUT
MITSUBISHI
MULTI-COMMUNICATION
SYSTEM (MMCS)>
HANDS-FREE CELLULAR PHONE SYSTEM
TSB Revision
CHASSIS ELECTRICAL
54A-491
.
FUNCTION
During the conversation with the hands free cellular
phone system, the signal of speaker's voice is trans-
mitted from the microphone unit to the hands free
module. Then the signal is transmitted from the
hands free module to the cellular phone. The voice of
other party is transmitted from the cellular phone to
the hands free module. Then, the voice is transmitted
from the hands free module to the radio and CD
player <vehicles without MMCS> or multivision dis-
play <vehicles with MMCS>, and output from the
speaker.
.
TROUBLE JUDGMENT CONDITIONS
If the hands free cellular phone system cannot be
used normally, the hands free module, microphone
unit, steering wheel voice control switch, or radio and
CD player <vehicles without MMCS> or multivision
display <vehicles with MMCS> may be defective.
.
TROUBLESHOOTING HINTS
• The hands free module may be defective.
• The microphone unit may be defective.
• The steering wheel voice control switch may be
defective.
• The radio and CD player <vehicles without
MMCS> or multivision display <vehicles with
MMCS> may be defective.
• Damaged harness wires and connectors
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB992006: Extra Fine Probe
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
AC708951BS
Connectors: C-10, C-11, C-109, C-110
C-10 (GR)
C-109,
C-110
C-11
AC708950
Connector: C-133
AF
AC708972AB
Connector: C-317
Junction block
AC708954 AT
Connector: D-04
HANDS-FREE CELLULAR PHONE SYSTEM
TSB Revision
CHASSIS ELECTRICAL
54A-492
STEP 1. Check the cellular phone.
Check that the cellular phone can be used normally as a unit.
Q: Is it possible to use the cellular phone normally?
YES : Go to Step 2.
NO : Repair or replace the cellular phone.
STEP 2. Temporarily replace the cellular phone, and check
the trouble symptom.
Temporarily register a separate Bluetooth
™-supported cellular
phone, and check that the hands-free cellular phone system
operates normally.
Q: Is the normal conversation possible with the hands free
cellular phone system?
YES : Ask the customer to have the cellular phone repaired
or replaced. Then, delete the temporarily registered
cellular phone. Once the customer prepares the
normally-working cellular phone, register the cellular
phone to the hands free module.
NO : Go to Step 3.
STEP 3. Using scan tool MB991958, diagnose the CAN bus
line.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect the
Scan Tool (M.U.T.-III)
."
(2) Turn the ignition switch to the "ON" position.
(3) Diagnose the CAN bus line.
(4) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the CAN bus line found to be normal?
YES : Go to Step 4.
NO : Repair the CAN bus line (Refer to GROUP 54C,
).
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст