Mitsubishi Outlander XL. Manual — part 839
ZC6007580000
1
Double-sided tape: 10 mm (0.39 in) width and 1.2 mm (0.05 in) thickness
Double-sided tape affixed location
<Rear roof garnish>
Rear roof garnish removal
·
·
Headlining (Refer to GROUP 52A,
Headlining P.52A-15)
1. Rear roof garnish
Liftgate garnish removal
·
Rear wiper motor (Refer to P.51B-49)
·
Liftgate trim (Refer to GROUP 52A,
Liftgate trim P.52A-14)
Liftgate garnish removal
>>A<< 2. Liftgate garnish
Liftgate lower garnish removal
·
Liftgate lower trim (Refer to GROUP 52A,
Liftgate lower trim P.52A-14)
3. Liftgate garnish cover
4. Liftgate lower garnish
Required Special Tool:
⦆
MB990784: Ornament remover
INSTALLATION SERVICE POINT
>>A<< LIFTGATE GARNISH INSTALLATION
ZC6003670000
Weatherstrip
Tape
Tape
Rear wiper
A
A
Section A – A
Liftgate
garnish
Weather-
strip
When installing the liftgate garnish, roll up the weatherstrip
and secure it with a tape as shown to avoid trapping it.
DOOR SASH TAPE
REMOVAL AND INSTALLATION
M15101000241USA0000010000
Pre-removal and post-installation operation
⦆
Door Trim Assembly Removal and Installation (Refer to GROUP 52A - Door Trim, P.52A-11).
⦆
Door Beltline Weatherstrip Inner Removal and Installation (Refer to GROUP 42Ab - Window Glass Runchannel and Door
Opening Weatherstrip P.42Ab-110).
⦆
Door Opening Weatherstrip Outer Removal and Installation (Refer to GROUP 42Ab - Window Glass Runchannel and Door
Opening Weatherstrip P.42Ab-110).
⦆
Door Window Glass Runchannel Removal and Installation (Refer to GROUP 42Ab - Window Glass Runchannel and Door
Opening Weatherstrip P.42Ab-110).
⦆
Door Beltline Molding Removal and Installation (Refer to GROUP 42Ab - Window Glass Runchannel and Door Opening
EXTERIOR
51A-11
DOOR SASH TAPE
ZC600447
1
2
3
N
N
N
0000
Removal steps
<<A>>
>>A<<
1.
Front door sash tape, rear
<<A>>
>>A<<
2.
Rear door sash tape, front
<<A>>
>>A<<
3.
Rear door sash tape, rear
Required Special Tool:
⦆
MB990528: Stripe Tape Spatula
REMOVAL SERVICE POINT
<<A>> DOOR SASH TAPES REMOVAL
Pay attention to keep from getting burned by hot door panel
or tapes.
1.
Use a hair drier to warm the tape.
2.
Peel the tip of the tape with your finger, and then peel off the
tape in parallel with the application surface.
51A-12
EXTERIOR
DOOR SASH TAPE
INSTALLATION SERVICE POINT
>>A<< DOOR SASH TAPES INSTALLATION
ZC5016230000
MB990528
Unit: mm(in)
MB990528
40 to 50°
30 to 45°
10 to 20
(0.39 to 0.79)
10 to 20
(0.39 to 0.79)
Door sash tape
Backing paper
Door sash tape
Backing paper
<Pushing direction>
<Pulling direction>
3 to 7 cm/sec.
3 to 7 cm/sec.
⦆
The ambient temperature should be 20 - 30 °C(68 - 86°F).
Ensure that the working area is clean. Ideally, the tape
application should be done at ambient temperature of 25°
C(77°F).
⦆
If ambient temperature is less than 15°C(59°F, heat the
tape and application surface to a temperature of 20 - 30 °
C(68 - 86°F). Alternatively, allow it to cool if it is 35°C(95°
F) or higher. The adhesive property of the tape is
deteriorated at low temperature, so the tape may come
adrift easily. Meanwhile, the tape will be softened
excessively at high temperature.
⦆
When beginning to apply the tape, pay particular
attention. If the end of the tape cannot be applied to the
specified position with an accuracy of less than 1 mm
(0.04 in), it may cause the poor appearance or adhesion.
⦆
When using the special tool, stripe tape spatula
(MB990528) to apply the tape, be sure to move it steadily,
evenly and without interruption. If you fail to do so, a
groove (usually known as shock line) may be left on the
tape surface. Meanwhile, if you move it too slowly, air
bubble may be left inside the tape. Keep even pressure,
constant speed and steady application angle when
moving the special tool.
1.
Wrap a soft cloth (synthetic fiber) around the tip of the special
tool.
2.
Use white gasoline to degrease the tape application surface.
3.
Wipe away dirt from the tape.
EXTERIOR
51A-13
DOOR SASH TAPE
ZC6004480000
4(0.16)
4(0.16)
4(0.16)
4(0.16)
4(0.16)
4(0.16)
4(0.16)
4(0.16)
1(0.04)
3(0.12)
3(0.12)
3(0.12)
3(0.12)
3(0.12)
: Tape locating points
: T-stud for door opening weatherstrip attaching locations (6 places in all).
Section A – A
Section D – D (*)
B
C
C
B
A
A
A
A
D
D
Section B – B
Section C – C
Unit: mm (in)
37(1.46)
30.9(1.22)(*)
ZC5016240000
MB990528
Backing paper
Door sash
tape
4.
Apply the door sash tape according to the procedure below.
(1)
Position the tape at the upper and lower locating points.
(2)
Peel of backing strip from the top of the tape and attach it
temporarily.
(3)
Peel off the backing strip to the half length of the tape.
(4)
Apply the tape using the special tool while peeling off the
remaining backing strip.
(5)
For the front rear door sash tape, apply it to plain surface
(A). Then apply it to stepped surface (B).
(6)
Press the folded area of the tape by three stages (60°, 120°
and holding), rolling in toward the vehicle inside direction.
51A-14
EXTERIOR
DOOR SASH TAPE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст