Mitsubishi Outlander XL. Manual — part 1198
Q:Is the check result satisfactory?
YES:
The procedure is complete.
NO:
Replace the A/C-ECU.
INSPECTION PROCEDURE 7: A/C Outlet Air Temperature does not Increase
M15502000958USA0000010000
Air Mixing Damper Control Motor Circuit
AIR MIXING
DAMPER CONTROL
MOTOR
A/C-ECU
ZC6008760040
Connector: C-08, C-115
C-108 (B)
C-115
CIRCUIT OPERATION
If the air outlet temperature cannot be adjusted, the
air mixing damper control motor circuit may be failed.
TROUBLESHOOTING HINTS
⦆
Malfunction of the air mixing damper control motor
⦆
Malfunction of the A/C-ECU
⦆
Damaged harness wires or connectors
DIAGNOSIS
Required Special Tools:
⦆
MB991223: Harness Set
⦆
MB992006: Extra Fine Probe
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: V.C.I.
AIR CONDITIONING
55A-83
MANUAL A/C DIAGNOSIS
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A
STEP 1. Using scan tool MB991958, read the diagnostic
trouble code.
Check if an A/C-ECU DTC is set.
(1)
Connect scan tool MB991958 to the data link connector.
(2)
Turn the ignition switch to the "ON" position.
(3)
Check if the DTC is set.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the check result satisfactory?
YES:
Go to Step 2.
NO:
Refer to DIAGNOSTIC TROUBLE CODE CHART P.55A-8.
STEP 2. Check air mixing damper control motor connector
C-115 and A/C-ECU connector C-108 for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
Q:Are air mixing damper control motor connector C-115 and
A/C-ECU connector C-108 in good condition?
YES:
Go to Step 3.
NO:
Repair or replace the connector. Refer to GROUP 00E,
Harness Connector Inspection P.00E-2. Check that the A/C
works normally.
STEP 3. Check the wiring harness between A/C-ECU
connector C-108 (terminal 29, 35, 36, 34 and 28) and air
mixing damper control motor connector C-115 (terminals 3,
2, 5. 4 and 1).
Q:Are the wiring harness between A/C-ECU connector
C-108 (terminal 29, 35, 36, 34 and 28) and air mixing
damper control motor connector C-115 (terminals 3, 2, 5.
4 and 1) in good condition?
YES:
Go to Step 4.
NO:
Repair the wiring harness. Check that the A/C works
normally.
STEP 4. Replace the power transistor and check the trouble
symptom again
Check the trouble symptom again.
Q:Is the check result satisfactory?
YES:
The procedure is complete.
NO:
Replace the A/C-ECU.
55A-84
AIR CONDITIONING
MANUAL A/C DIAGNOSIS
INSPECTION PROCEDURE 8: Air Outlet Vent cannot be Changed.
M15502000959USA0000010000
Mode Selection Damper Control Motor Circuit
MODE SELECTION
DAMPER CONTROL
MOTOR
A/C-ECU
ZC600876
Connectors: C-108, C-130
C-108 (B)
C-107
CIRCUIT OPERATION
If the air outlet cannot be switched, the mode selection
damper control motor circuit may be failed.
TROUBLESHOOTING HINTS
⦆
Malfunction of the mode selection damper control
motor
⦆
Malfunction of the A/C-ECU
⦆
Damaged harness wires or connectors
DIAGNOSIS
Required Special Tools:
⦆
MB991223: Harness Set
⦆
MB992006: Extra Fine Probe
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: V.C.I.
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A
AIR CONDITIONING
55A-85
MANUAL A/C DIAGNOSIS
STEP 1. Using scan tool MB991958, read the diagnostic
trouble code.
Check if an A/C-ECU DTC is set.
(1)
Connect scan tool MB991958 to the data link connector.
(2)
Turn the ignition switch to the "ON" position.
(3)
Check if the DTC is set.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the check result satisfactory?
YES:
Go to Step 2.
NO:
Refer to DIAGNOSTIC TROUBLE CODE CHART P.55A-8.
STEP 2. Check mode selection damper control motor
connector C-107 and A/C-ECU connector C-108 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q:Are mode selection damper control motor connector
C-107 and A/C-ECU connector C-108 in good condition?
YES:
Go to Step 3.
NO:
Repair or replace the connector. Refer to GROUP 00E,
Harness Connector Inspection P.00E-2. Check that the A/C
works normally.
STEP 3. Check the wiring harness between A/C-ECU
connector C-108 (terminal 29, 31, 32, 30 and 33) and mode
selection damper control motor connector C-107 (terminals
3, 2, 5. 4 and 1).
Q:Are the wiring harness between A/C-ECU connector
C-108 (terminal 29, 31, 32, 30 and 33) and mode selection
damper control motor connector C-107 (terminals 3, 2, 5.
4 and 1) in good condition?
YES:
Go to Step 4.
NO:
Repair the wiring harness. Check that the A/C works
normally.
STEP 4. Replace the power transistor and check the trouble
symptom again
Check the trouble symptom again.
Q:Is the check result satisfactory?
YES:
The procedure is complete.
NO:
Replace the A/C-ECU.
55A-86
AIR CONDITIONING
MANUAL A/C DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст