Mitsubishi Outlander XL. Manual — part 736
ZC6006090000
(2)
Connect a battery to the motor terminal, and check that the
motor runs freely.
Battery connection
Slider position
⦆
Connect terminal 1 to
the negative battery
terminal
⦆
Connect terminal 4 to
the positive battery
terminal
UP
⦆
Connect terminal 4 to
the negative battery
terminal
⦆
Connect terminal 1 to
the positive battery
terminal
DOWN
Q:Is the front power window motor (RH) normal?
YES:
Go to Step 7.
NO:
Replace the front power assembly (RH). When the front
power window sub switch (RH) is operated, the front power
window (RH) should raise and lower normally.
STEP 7. Check the battery power supply circuit to the front
power window sub switch. Measure the voltage at front
power window sub switch connector E-06.
(1)
Disconnect front power window sub switch connector E-06
and measure the voltage available at the wiring harness side
of the connector.
ZC500795
Connector E-06
(harness side)
0005
(2)
Measure the voltage between terminal 6 and ground.
⦆
The voltage should measure approximately 12 volts
(battery positive voltage).
Q:Is the measured voltage approximately 12 volts (battery
positive voltage)?
YES:
Go to Step 10.
NO:
Go to Step 8.
STEP 8. Check ETACS-ECU connector C-315 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q:Is ETACS-ECU connector C-315 in good condition?
YES:
Go to Step 9.
NO:
Repair or replace the damaged component(s). Refer to
GROUP 00E, Harness Connector Inspection P.00E-2. When the
front power window sub switch (RH) is operated, the front
power window (RH) should raise and lower normally.
DOOR
42Ab-63
POWER WINDOW DIAGNOSIS
STEP 9. Check the wiring harness between ETACS-ECU
connector C-315 (terminal 8) and front power window sub
switch connector E-06 (terminal 6).
NOTE:
Also check intermediate connector C-112. If
intermediate connectors C-112 is damaged, repair or replace
the damaged component(s) as described in GROUP 00E, Harness
Connector Inspection P.00E-2.
Q:Is the wiring harness between ETACS-ECU connector
C-315 (terminal 8) and front power window sub switch
connector E-06 (terminal 6 in good condition?
YES:
No action is necessary and testing is complete.
NO:
The wiring harness may be damaged or the connector
(s) may have loose, corroded or damaged terminals, or
terminals pushed back in the connector. Repair the wiring
harness as necessary. When the front power window sub
switch is operated, the front power window (RH) should
raise and lower normally.
STEP 10. Check the ground circuit to the front power
window sub switch. Measure the resistance at front power
window sub switch connector E-06.
(1)
Disconnect front power window sub switch connector E-19
and measure the resistance available at the wiring harness
side of the connector.
ZC5007880005
Connector E-06
(harness side)
(2)
Measure the resistance value between terminal 5 and
ground, and also between terminal 8 and ground.
⦆
The resistance should be 2 ohms or less.
Q:Is the measured resistance 2 ohms or less?
YES:
Go to Step 12.
NO:
Go to Step 11.
STEP 11. Check the wiring harness between power window
main switch connector E-19 (terminals 1 and 3) and front
power window sub switch connector E-06 (terminals 8 and
5).
NOTE:
Also check intermediate connectors C-112 and C-126.
If intermediate connector C-112 or C-126 is damaged, repair
or replace the damaged component(s) as described in GROUP
00E, Harness Connector Inspection P.00E-2.
Q:Is the wiring harness between power window main switch
connector E-19 (terminals 1 and 3) and front power
window sub switch connector E-06 (terminals 8 and 5) in
good condition?
YES:
Replace the power window main switch. When the front
power window sub switch (RH) is operated, the front power
window (RH) should raise and lower normally.
NO:
The wiring harness may be damaged or the connector
(s) may have loose, corroded or damaged terminals, or
42Ab-64
DOOR
POWER WINDOW DIAGNOSIS
terminals pushed back in the connector. Repair the wiring
harness as necessary. When the front power window sub
switch (RH) is operated, the front power window (RH)
should raise and lower normally.
STEP 12. Check the wiring harness between front power
window sub switch connector E-06 (terminals 4 and 7) and
front power window motor (RH) connector E-03 (terminals
1 and 4).
Q:Is the wiring harness between front power window sub
switch connector E-06 (terminals 4 and 7) and front power
window motor (RH) connector E-03 (terminals 1 and 4) in
good condition?
YES:
No action is necessary and testing is complete.
NO:
The wiring harness may be damaged or the connector
(s) may have loose, corroded or damaged terminals, or
terminals pushed back in the connector. Repair the wiring
harness as necessary. When the front power window sub
switch (RH) is operated, the front power window (RH)
should raise and lower normally.
STEP 13. Check rear power window sub switch (LH)
connector E-25 and rear power window motor (LH)
connector E-26 for loose, corroded or damaged terminals,
or terminals pushed back in the connector.
Q:Are rear power window sub switch (LH) connector E-25
and rear power window motor (LH) connector E-26 in
good condition?
YES:
Go to Step 14.
NO:
Repair or replace the damaged component(s). Refer to
GROUP 00E, Harness Connector Inspection P.00E-2. When the
rear power window sub switch (LH) is operated, the rear
power window (LH) should raise and lower normally.
STEP 14. Check the rear power window sub switch (LH) for
continuity.
(1)
Remove the rear power window sub switch (LH). Refer to
GROUP 42Ab, Door, Door Glass and Regulator P.
42Ab-97.
ZC6013730000
8
3
4 5
1
2
6 7
<Rear door>
(2)
Check continuity when the rear power window sub switch
(LH) is operated to "UP" or "DOWN" position.
Switch
position
Tester
connection
Specified
condition
UP
4 - 5, 6 - 7
Continuity
exists (2 Ω or
less)
OFF
4 - 5, 7 - 8
DOWN
4 - 6, 7 - 8
Q:Is the rear power window sub switch (LH) normal?
YES:
Go to Step 15.
NO:
Replace the rear power window sub switch (LH). When
the rear power window sub switch (LH) is operated, the
rear power window (LH) should raise and lower normally.
DOOR
42Ab-65
POWER WINDOW DIAGNOSIS
STEP 15. Check the rear power window motor (LH).
(1)
Remove the rear power window regulator assembly (LH).
Refer to GROUP 42Ab, Door, Door Glass and Regulator P.
42Ab-97.
ZC6006080000
(2)
Connect a battery to the motor terminal, and check that the
motor runs freely.
Battery connection
Slider position
⦆
Connect terminal 1 to
the negative battery
terminal
⦆
Connect terminal 4 to
the positive battery
terminal
UP
⦆
Connect terminal 4 to
the negative battery
terminal
⦆
Connect terminal 1 to
the positive battery
terminal
DOWN
Q:Is the rear power window motor (LH) normal?
YES:
Go to Step 16.
NO:
Replace the rear power window motor (LH). When the
rear power window sub switch (LH) is operated, the rear
power window (LH) should raise and lower normally.
STEP 16. Check the battery power supply circuit to the rear
power window sub switch (LH). Measure the voltage at rear
power window sub switch (LH) connector E-25.
(1)
Disconnect rear power window sub switch (LH) connector
E-25 and measure the voltage available at the wiring harness
side of the connector.
ZC500795
Connector E-25
(harness side)
0007
(2)
Measure the voltage between terminal 6 and ground.
⦆
The voltage should measure approximately 12 volts
(battery positive voltage).
Q:Is the measured voltage approximately 12 volts (battery
positive voltage)?
YES:
Go to Step 19.
NO:
Go to Step 17.
STEP 17. Check ETACS-ECU connector C-311 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q:Is ETACS-ECU connector C-311 in good condition?
YES:
Go to Step 18.
NO:
Repair or replace the damaged component(s). Refer to
GROUP 00E, Harness Connector Inspection P.00E-2. When the
rear power window sub switch (LH) is operated, the rear
power window (LH) should raise and lower normally.
42Ab-66
DOOR
POWER WINDOW DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст