Mitsubishi Outlander XL. Manual — part 580
Inspection Procedure 2: The Switch Position of the Drive Mode Selector does not Match
with the Indicator Display in the Combination Meter.
M12704100032USA0000010000
ETACS-
ECU
IGNITION
SWITCH (IG1)
IG1
RELAY
AWD-ECU
DRIVE MODE
SELECTOR
D7G27M001A00
GREY
WHITE
BLA
CK
BLA
CK
BLA
CK
VIOLET
VIOLET
LIGHT
GREEN
LIGHT
GREEN
C-128
C-32
C-23
ZC6000240001
Connectors: C-32, C-128
C-128
C-32
ZC6000260001
ETACS-ECU
(front view)
C-313
(BR)
C-317
Connectors: C-313, C-317
ELECTRONIC CONTROL AWD
27C-79
DIAGNOSIS
ZC6000350000
C-23
Connector: C-23
DRIVE MODE SELECTOR POSITION AND INDICATOR
DISPLAY (NORMAL)
ZC6000190000
Drive mode indicator
Vehicles for USA
ZC6000200000
Drive mode indicator
Vehicles for Canada
ZC6000130000
Drive mode
selector
Switch position
Indicator display
FWD (2WD)
-(Not illuminated)
AWD (4WD)
AWD
LOCK
AWD, LOCK
27C-80
ELECTRONIC CONTROL AWD
DIAGNOSIS
COMMENTS ON TROUBLE SYMPTOM
⦆
If the drive mode selector switch position and indicator display
in the combination meter do not match, the drive mode
selector, wiring harness connector between AWD-ECU and
drive mode selector, wiring harness connector in the earth
circuit for the drive mode selector, or AWD-ECU may have a
problem.
⦆
If high-pressure type spare tires are equipped, tire pressure is
excessively out of the specified value, or tires with different
sizes or different brands are equipped, AWD mode may be
temporarily displayed even when the LOCK mode is selected.
TROUBLESHOOTING HINTS
⦆
Damaged wiring harness and connectors
⦆
Malfunction of drive mode selector
⦆
AWD-ECU malfunction
⦆
High-pressure type spare tires are equipped, tire
pressure is excessively out of the specified value,
or tires with different sizes or different brands are
equipped
DIAGNOSIS
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicle Communication Interface
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A
NOTE:
Be sure to ask the user if any of the probable causes
is applicable before performing the diagnosis procedure.
STEP 1. Check the following connector:
Check the C-23 drive mode selector connector and C-128 AWD-
ECU connector for improper engagement, terminal damage or
terminal drawn in the connector case.
Q:Are the connectors and terminals in good condition?
YES:
Go to Step 2.
NO:
Repair the connector(s) or terminal(s). Then go to
Step 9.
STEP 2. Resistance measurement between the drive mode
selector connector terminals
ZC3052090001
(1)
Remove the drive mode selector (Refer P.27C-93.)
ELECTRONIC CONTROL AWD
27C-81
DIAGNOSIS
ZC3047570000
C-23 drive mode
selector connector:
component side
(2)
Measure the resistance between the following terminals.
Switch position
Terminal
number
Normal
conditions
FWD
1 - 2
Continuity
exists (2 ohm
or less).
AWD
-
No continuity
LOCK
2 - 3
Continuity
exists (2 ohm
or less).
Q:Is the check result normal?
YES:
Go to Step 3.
NO:
Replace the drive mode selector. Then go to Step 9.
STEP 3. Wiring harness check
⦆
Wiring harness between the C-128 AWD-ECU connector
(terminal No. 16) and the C-23 drive mode selector connector
(terminal No. 3)
⦆
Wiring harness between the C-128 AWD-ECU connector
(terminal No. 14) and the C-23 drive mode selector connector
(terminal No. 1)
Check the wiring harness above for damage or other problem.
Q:Is the wiring harness in good condition?
YES:
Go to Step 4.
NO:
Repair the wiring harness. Then go to Step 9.
STEP 4. Resistance measurement at the drive mode
selector connector
(1)
Disconnect the C-23 drive mode selector connector.
ZC3047230000
C-23 harness
connector:
harness side
(2)
Measure the resistance between the C-23 wiring harness
side connector terminal No. 4 and the body earth.
OK: 2 ohm or less
Q:Is the check result normal?
YES:
Go to Step 8.
NO:
Go to Step 5.
STEP 5. Wiring harness check
NOTE:
Prior to the wiring harness inspection, check the
C-32 joint connector, and repair if necessary.
27C-82
ELECTRONIC CONTROL AWD
DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст