Mitsubishi Outlander XL. Manual — part 1049
STEP 5. Check the wiring harness between driver's door
switch connector D-23 (terminal 3) and ETACS-ECU
connector C-313 (terminal 16).
Q:Is the wiring harness between driver's door switch
connector D-23 (terminal 3) and ETACS-ECU connector
C-313 (terminal 16) in good condition?
YES:
Replace the ETACS-ECU. Check that the input signal
of front door switch (LH) is normal.
NO:
The wiring harness may be damaged or the connector
(s) may have loose, corroded or damaged terminals, or
terminals pushed back in the connector. Repair the wiring
harness as necessary. Check that the input signal of front
door switch (LH) is normal.
Inspection Procedure 6: ETACS-ECU does not receive any signal from the front door
switch (RH).
M15410600069USA0000010000
ETACS-
ECU
FRONT DOOR
SWITCH (RH)
Front Door Switch (RH) Input Circuit
ZC6008780018
Connector: C-313
C-313 (BR)
ZC6008790008
Connector: D-35
ETACS
54Ad-75
DIAGNOSIS
TECHNICAL DESCRIPTION (COMMENT)
If there is an error to the front door switch (RH) input
signal, the front door switch (RH) signal is no longer
output to the communication line.
TROUBLESHOOTING HINTS
⦆
The front door switch (RH) may be defective
⦆
The ETACS-ECU may be defective
⦆
The wiring harness or connectors may have loose,
corroded, or damaged terminals, or terminals
pushed back in the connector
DIAGNOSIS
Required Special Tools:
⦆
MB991223: Harness Set
⦆
MB992006: Extra Fine Probe
STEP 1. Check front door switch (RH) connector D-35 for
loose, corroded or damaged terminals, or terminals pushed
back in the connector.
Q:Is front door switch (RH) connector D-35 in good
condition?
YES:
Go to Step 2.
NO:
Repair or replace the damaged component(s). Refer to
GROUP 00E, Harness Connector Inspection P.00E-2. Check
that the input signal of front door switch (RH) is normal.
STEP 2. Check the front door switch (RH).
Remove the front door switch (RH). Then check the continuity
between the switch terminals and the switch body.
Switch position
Tester
connection
Specified condition
Released
3 - switch body
Less than 2 ohms
Pressed
3 - switch body
Open circuit
Q:Is the front door switch (RH) in good condition?
YES:
Go to Step 3.
NO:
Replace the front door switch (RH). Check that the
input signal of front door switch (RH) is normal.
STEP 3. Measure at the lower metal part of the front door
switch (RH) in order to check the ground circuit to the front
door switch (RH).
NOTE:
Check that the front door switch (RH) is grounded to
the vehicle body by means of its mounting screw.
Remove the cap, and measure the resistance value between the
lower metal part and the ground.
⦆
The resistance should equal 2 ohms or less.
Q:Is the measured resistance 2 ohms or less?
YES:
Go to Step 4.
NO:
Check the fit of the switch, and repair if necessary.
Check that the input signal of front door switch (RH) is
normal.
54Ad-76
ETACS
DIAGNOSIS
STEP 4. Check ETACS-ECU connector C-313 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q:Is ETACS-ECU connector C-313 in good condition?
YES:
Go to Step 5.
NO:
Repair or replace the damaged component(s). Refer to
GROUP 00E, Harness Connector Inspection P.00E-2. Check
that the input signal of front door switch (RH) is normal.
STEP 5. Check the wiring harness between front door
switch (RH) connector D-35 (terminal 3) and ETACS-ECU
connector C-313 (terminal 12).
Q:Is the wiring harness between driver's door switch
connector D-35 (terminal 3) and ETACS-ECU connector
C-313 (terminal 12) in good condition?
YES:
Replace the ETACS-ECU. Check that the input signal
of front door switch (RH) is normal.
NO:
The wiring harness may be damaged or the connector
(s) may have loose, corroded or damaged terminals, or
terminals pushed back in the connector. Repair the wiring
harness as necessary. Check that the input signal of front
door switch (RH) is normal.
Inspection Procedure 7: ETACS-ECU does not receive any signal from the rear door
switch (LH).
M15410600072USA0000010000
ETACS-
ECU
REAR DOOR
SWITCH (LH)
Rear Door Switch (LH) Input Circuit
ETACS
54Ad-77
DIAGNOSIS
ZC6008780018
Connector: C-313
C-313 (BR)
ZC6008800009
Connector: D-17
TECHNICAL DESCRIPTION (COMMENT)
If there is an error to the rear door switch (LH) input
signal, the rear door switch (LH) signal is no longer
output to the communication line.
TROUBLESHOOTING HINTS
⦆
The rear door switch (LH) may be defective
⦆
The ETACS-ECU may be defective
⦆
The wiring harness or connectors may have loose,
corroded, or damaged terminals, or terminals
pushed back in the connector
DIAGNOSIS
Required Special Tools:
⦆
MB991223: Harness Set
⦆
MB992006: Extra Fine Probe
STEP 1. Check rear door switch (LH) connector D-17 for
loose, corroded or damaged terminals, or terminals pushed
back in the connector.
Q:Is rear door switch (LH) connector D-17 in good
condition?
YES:
Go to Step 2.
NO:
Repair or replace the damaged component(s). Refer to
GROUP 00E, Harness Connector Inspection P.00E-2. Check
that the input signal of rear door switch (LH) is normal.
STEP 2. Check the rear door switch (LH).
Remove the rear door switch (LH). Then check the continuity
between the switch terminals and the switch body.
Switch position
Tester
connection
Specified condition
Released
3 - switch body
Less than 2 ohms
Pressed
3 - switch body
Open circuit
Q:Is the rear door switch in good condition?
YES:
Go to Step 3.
NO:
Replace the rear door switch (LH). Check that the
input signal of rear door switch (LH) is normal.
54Ad-78
ETACS
DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст