Mitsubishi Outlander XL. Manual — part 226

STEP 6. Test the OBD-II drive cycle.

(1)

Carry out a test drive with the drive cycle pattern. Refer to
Diagnostic Function - OBD-II Drive Cycle - Pattern 2 P.
13Ab-8.

(2)

Check the diagnostic trouble code (DTC).

Q:Is DTC P0057 set?

YES:

Retry the troubleshooting.

NO:

The inspection is complete.

MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>

13Ab-99

DIAGNOSTIC TROUBLE CODE PROCEDURES

DTC P0058: Heated Oxygen Sensor Heater Control Circuit High (bank 2, sensor 2)

M11310100168USA0000010000

ZK602832

1

3

2

4

1

2

3 4 5 6 7 8 9 10 11 12 13 14 15 16

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

1

10 111213 14 1516 17 1819 20

2 3 4

5 6 7 8 9

2

1

4

3

AA00

20A

WHITE

BR

O

WN

WHITE

WHITE

WHITE

A-33X

MFI
RELAY

RELAY BOX
(ENGINE COMPARTMENT)

4

3

1

2

22

TO ECM

LEFT BANK HEATED
OXYGEN SENSOR (REAR)

1

2

3

4

TO ECM TO ECM

ENGINE
CONTROL
MODULE

35

4

LEFT BANK HEATED OXYGEN SENSOR (REAR) HEATER CIRCUIT

B-13

MU802665

B-10

A-13

OFF

ON

36

FUSIBLE LINK

13Ab-100

MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>

DIAGNOSTIC TROUBLE CODE PROCEDURES

ZK603589

MFI relay

A-33X

Connector: A-33X

AA00

ZK603595AA00

Left bank heated
oxygen sensor (rear)

Front
exhaust pipe

B-13 (GR)

Connector: B-13

ZK603591

ECM

B-10 (GR)

Connector: B-10

AA00

ZK603650AA00

A-13

Connector: A-13

CIRCUIT OPERATION

｠

Power is supplied from the MFI relay (terminal No.
4) to the left bank heated oxygen sensor (rear)
heater.

｠

The ECM (terminal No. 49) controls continuity to the
left bank heated oxygen sensor (rear) heater by
turning the power transistor in the ECM "ON" and
"OFF".

BACKGROUND

｠

The ECM checks whether the heater current is
within a specified range when the heater is
energized.

DESCRIPTIONS OF MONITOR METHODS

Left bank heated oxygen sensor heater (rear)
current is out of specified range.

MONITOR EXECUTION

Continuous

MONITOR EXECUTION CONDITIONS (Other
monitor and Sensor)

Other Monitor (There is no temporary DTC stored in
memory for the item monitored below)

｠

Not applicable

Sensor (The sensor below is determined to be
normal)

｠

Not applicable

MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>

13Ab-101

DIAGNOSTIC TROUBLE CODE PROCEDURES

DTC SET CONDITION

Logic Flow Chart

Start

End

Yes

Yes

Yes

No

No

No

Malfunction

Good

Continuous

failure for 2secs

Monitoring

conditions

Current < 0.17A

or

Current > 10.5A

Voltage < 2.0V

ZK603657 AA00

Heater ON

Yes

Yes

No

Check Conditions

｠

More than 2 seconds have passed since the engine
starting sequence was completed.

｠

While the left bank heated oxygen sensor (rear)
heater is on.

｠

Battery positive voltage is between 11 and 16.5
volts.

Judgement Criterion

｠

The left bank heated oxygen sensor (rear) heater
current has continued to be higher than 10.5
ampere for 2 seconds.

OBD-II DRIVE CYCLE PATTERN

Refer to Diagnostic Function - OBD-II Drive Cycle -
Pattern 2 P.13Ab-8.

TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are: )

｠

Left bank heated oxygen sensor (rear) heater failed.

｠

Left bank heated oxygen sensor (rear) failed.

｠

ECM failed.

13Ab-102

MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>

DIAGNOSTIC TROUBLE CODE PROCEDURES