Mitsubishi Outlander XL. Manual — part 356
YES:
Replace the ECM. When the ECM is replaced, register
the ID code. Refer to GROUP 42B, ID Code Registration
Judgment Table <Vehicles with KOS> P.42B-12or GROUP
42C, ID Code Registration Judgment Table <Vehicles with
WCM> P.42C-8. Then go to Step 8.
NO:
The Inspection is complete.
STEP 8. Test the OBD-II Drive Cycle.
(1)
Carry out test drive with the drive cycle pattern. Refer to
Diagnostic Function - OBD-II Drive Cycle - Pattern 21 P.
13Ab-8.
(2)
Check the diagnostic trouble code (DTC).
Q:Is DTC P1020 set?
YES:
Retry the trouble shooting.
NO:
The Inspection is complete.
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
13Ab-619
DIAGNOSTIC TROUBLE CODE PROCEDURES
DTC P1021: Engine Oil Control Valve Circuit
M11310100252USA0000010000
2
1
ZK602859
1
2
3 4 5 6 7 8 9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
1
3
2
4
1
10 111213 14 1516 17 1819 20
2 3 4
5 6 7 8 9
1
2
1
B-106
MU802779
ENGINE
CONTROL
MODULE
B-10
20A
WHITE
WHITE
WHITE
VIOLET
WHITE
A-33X
MFI
RELAY
RELAY BOX
(ENGINE COMPARTMENT)
4
3
1
2
22
TO ECM
OFF
ON
AA00
ENGINE OIL CONTROL VALVE CIRCUIT
ENGINE OIL
CONTROL VALVE
36
FUSIBLE LINK
4
A-13
13Ab-620
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
DIAGNOSTIC TROUBLE CODE PROCEDURES
ZK603631
Engine oil
control valve
AA00
B-106 (B)
Connector: B-106
ZK603589
MFI relay
A-33X
Connector: A-33X
AA00
ZK603591
ECM
B-10 (GR)
Connector: B-10
AA00
ZK603650AA00
A-13
Connector: A-13
CIRCUIT OPERATION
⦆
The engine oil control valve power is supplied from
the MFI relay (terminal No. 2).
⦆
The ECM controls ground engine oil control valve
by turning the power transistor in the ECM "ON" and
"OFF".
TECHNICAL DESCRIPTION
⦆
The engine oil pressure switches the cams to
operate the MIVEC system in the low-speed or
high-speed mode in accordance with the signals
from the ECM.
DESCRIPTIONS OF MONITOR METHODS
Circuit voltage stays low when solenoid status is off.
MONITOR EXECUTION
Continuous
MONITOR EXECUTION CONDITIONS (Other
monitor and Sensor)
Other Monitor (There is no temporary DTC stored in
memory for the item monitored below)
⦆
Not applicable
Sensor (The sensor below is determined to be
normal)
⦆
Not applicable
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
13Ab-621
DIAGNOSTIC TROUBLE CODE PROCEDURES
DTC SET CONDITIONS
Logic Flow Chart
ZK603802AA00
Good
Malfunction
Start
End
No
No
Yes
Yes
Yes
No
Monitoring
conditions
Continuous
failure for 2secs
Circuit voltage
< 1.5V
Check Conditions
⦆
Ignition switch: "ON"
⦆
Right bank engine oil control valve is OFF.
⦆
Battery positive voltage is between10 and 16.5
volts.
⦆
0.1 seconds has elapsed after the above mentioned
conditions have been met.
Judgment Criterion
⦆
The ECM terminal voltage of right bank engine oil
control valve circuit is less than 1.5 volts for 2
seconds.
OBD-II DRIVE CYCLE PATTERN
Refer to Diagnostic Function - OBD-II Drive Cycle -
Pattern 24 P.13Ab-8.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
⦆
Connector damage.
⦆
Harness damage.
⦆
Engine oil control valve failed.
⦆
ECM failed.
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: V.C.I.
⦆
MB991827: USB Cable
13Ab-622
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
DIAGNOSTIC TROUBLE CODE PROCEDURES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст