Mitsubishi Outlander XL. Manual — part 389
DTC SET CONDITIONS
Logic Flow Chart
Start
End
No
No
Yes
Yes
Yes
No
Malfunction
Continuous Failure
for specified time
Monitoring
Conditions
ZK604051AA00
Communication status
Fails
Good
Check Conditions
⦆
After 4 seconds have passed since the ignition
switch was turned to "ON" position.
⦆
Battery positive voltage is between 10 and 16.5
volts.
Judgement Criterion
⦆
The communication between the Meter-ECU
andthe ETACS-ECU has been down through the
CAN bus line for 4 seconds.
OBD-II DRIVE CYCLE PATTERN
None.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
⦆
CAN line harness damage or connector damage.
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan tool (M.U.T.-III Sub Assembly)
⦆
MB991824: V.C.I.
⦆
MB991827: USB Cable
⦆
MB991910: Main Harness A
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
13Ab-751
DIAGNOSTIC TROUBLE CODE PROCEDURES
STEP 1. Using scan tool MB991958, diagnose CAN bus line.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting san tool MB991958.
(1)
Connect scan tool MB991958 to the data link connector.
(2)
Turn the ignition switch to the "ON" position.
(3)
Diagnose CAN bus line.
(4)
Turn the ignition switch the "LOCK" (OFF) position.
Q:Is the CAN bus line normal?
YES:
It can be assumed that this malfunction is
intermittent. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points - How to Cope
with Intermittent Malfunctions P.00-15.
NO:
Repair the CAN bus line. Refer to GROUP 54D, Can bus
Diagnostics Table P.54D-10. Then go to Step 2.
STEP 2. Recheck for diagnostic trouble code.
Check again if the DTC is set.
(1)
Erase the DTC.
(2)
Turn the ignition switch to the "ON" position.
(3)
Check if DTC is set.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is DTC U1180 set?
YES:
Retry the troubleshooting.
NO:
The inspection is complete.
13Ab-752
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
DIAGNOSTIC TROUBLE CODE PROCEDURES
SYMPTOM PROCEDURES
INSPECTION PROCEDURE 1: Scan Tool Communication with ECM Is Not Possible.
M11310100081USA0000010001
71 72 73 74 75 76 77 78 79 80 81 82
83 84 85 86 87 88 89 90 91 92 93 94
95 96 97 98 99
100 101 102 103 104
112 113 114
109
108
107
110 111
115 116
106
105
118
117
1 2 3 4 5 6
12
11
10
1516
14
13
9
7 8
ZK602868
1
12 13 14 15 16 1718 19 20 2122 2324
2 3 4 5
6 7 8 9 10 11
1
12 13 14 15 16 1718 19 20 2122 2324
2 3 4 5
6 7 8 9 10 11
1
12 13 14 15 16 1718 19 20 2122 2324
2 3 4 5
6 7 8 9 10 11
2
8
7
6
5
4
3
11
21
20
19
18
17
16
15
14
13
12
9
22
1
10
1 2 3 4
5 6 7
15
14
13
12
11
10
9
8
1 2
FUSIBLE LINK
1
C-309
8
C-317
5
4
16
4
5
7
8
10
8
80
B-11
C-317
C-301
C-309
C-01
C-04
C-33
103
90
91
4
15
5
16
J/C (CAN3)
C-01
J/C (CAN2)
C-04
7
20
6
19
9
C-301
8
21
C-33
20
C-33
ENGINE
CONTROL
MODULE
DATA LINK
CONNECTOR
C-125
ETACS-ECU
6
14
10A
RED
BLA
CK
WHITE
BLA
CK
BLA
CK
BLA
CK
ORANGE
YELLO
W
PINK
YELLO
W
BLACK
YELLO
W
-GREEN
YELLO
W
-BLUE
YELLO
W
-BLUE
VIOLET
GREEN
GREEN-
WHITE
GREEN-
WHITE
GREEN-
RED
GREEN
34
5
ANALOG
INTERFACE
ANALOG
INTERFACE
INTERFACE
CAN DRIVER
INTERFACE
CAN DRIVER
AA00
CAN COMMUNICATION CIRCUIT
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
13Ab-753
SYMPTOM PROCEDURES
ZK603637
Data link connector
Brakepedal
AA00
C-125 (B)
Connector: C-125
ZK603655
C-01
Connector: C-01
AA00
ZK603592
ECM
B-11 (GR)
Connector: B-11
AA00
ZK603654AA00
C-33
Connector: C-33
ZK603645 AA00
ETACS-ECU
C-317
Connectors: C-301, C-309 and C-317
C-301
C-309 (B)
ZK603656
C-04
Connector: C-04
AA00
CIRCUIT OPERATION
⦆
Battery voltage is applied to the diagnosis
connector (terminal No. 16).
⦆
The diagnosis connector (terminal No. 4 and No. 5)
is grounded to the vehicle body.
COMMENT
⦆
When the communication between M.U.T.-III and
ECM is impossible, it can be suspected that the
CAN bus line, power supply circuit of the diagnosis
connector, and/or grounding circuit are defective.
⦆
Communication can not be achieved either, if a
wrong vehicle type is selected on M.U.T.-III.
13Ab-754
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
SYMPTOM PROCEDURES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст