Mitsubishi Outlander XL. Manual — part 504
INSPECTION PROCEDURE 6: The torque converter is not locked up.
M12301000444USA0000010000
TROUBLESHOOTING HINTS (THE MOST LIKELY
CAUSES FOR THIS CONDITION:)
⦆
Poor adjustment of transmission range switch
⦆
Failure of the transmission range switch main unit
⦆
Malfunction of the TCM
⦆
Poor installation of A/T and engine
⦆
Malfunction of the torque converter
DIAGNOSIS
STEP 1. Check and adjust the transmission range switch.
Refer to P.23A-157, P.23A-157.
If the transmission range switch has a failure, replace it, and then
check the trouble symptom again.
Q:Is the check result normal?
YES:
The procedure is complete.
NO:
Go to Step 2.
STEP 2. Replace the TCM.
Q:Is the failure resolved?
YES:
The procedure is complete.
NO:
Go to Step 3.
STEP 3. Check the installation position of the transaxle
assembly and the engine.
Is the installation of transaxle assembly and the engine normal?
Compare and check the axial direction position with the same
model vehicle.
Q:Is the check result normal?
YES:
Go to Step 4.
NO:
Repair the installation.
STEP 4. Check the transmission fluid.
Check the transmission fluid for burning, fouling, and foreign
material.
Q:Is the check result normal?
YES:
Replace the torque converter.
NO:
Replace the transaxle assembly..
INSPECTION PROCEDURE 7: The clutch slips when the vehicle starts or during gear
shift.
M12301000445USA0000010000
TROUBLESHOOTING HINTS (THE MOST LIKELY
CAUSES FOR THIS CONDITION:)
⦆
Poor adjustment of transaxle control cable
⦆
Inadequate transmission fluid level
⦆
A/T failure: Hydraulic system (valve body
assembly), driving force transmission system
(clutch/brake)
AUTOMATIC TRANSAXLE MECHANICAL
23A-131
AUTOMATIC TRANSAXLE DIAGNOSIS
DIAGNOSIS
STEP 1. Check the transaxle control cable. <When the
clutch slips at vehicle start>
Check the installation status of transaxle control cable and
transmission range switch.
Q:Is the check result normal?
YES:
Go to Step 2.
NO:
Adjust the installation status of transaxle control
cable and transmission range switch. P.23A-157.
STEP 2. Check the transmission fluid.
Check the transmission fluid for seizure, fouling, and foreign
material.
Q:Is the check result normal?
YES:
Go to Step 3.
NO:
Go to Step 5.
STEP 3. Check the transmission fluid level.
Check if the transmission fluid level is adequate.
Q:Is the check result normal?
YES:
Go to Step 4.
NO:
Check and repair the leakage point of the
transmission fluid, add the transmission fluid, and then
go to Step 4.
STEP 4. Perform a hydraulic test.
Refer to P.23A-21.
Q:Is the check result normal?
YES:
The procedure is complete.
NO:
Go to Step 5.
STEP 5. Remove the transaxle assembly from the vehicle.
Disassemble and check the transaxle assembly to check if there
is a foreign material inside.
Q:Is the check result satisfactory?
YES:
Replace the transaxle assembly.
NO:
Replace the failure part.
INSPECTION PROCEDURE 8: The engine brake is not applied.
M12301000446USA0000010000
TROUBLESHOOTING HINTS (THE MOST LIKELY
CAUSES FOR THIS CONDITION:)
⦆
Poor adjustment of transaxle control cable
⦆
Inadequate transmission fluid level
⦆
Malfunction of the TCM
⦆
A/T failure: Hydraulic system (valve body
assembly), driving force transmission system
(clutch/brake)
DIAGNOSIS
23A-132
AUTOMATIC TRANSAXLE MECHANICAL
AUTOMATIC TRANSAXLE DIAGNOSIS
STEP 1. Check the transaxle control cable.
Check the installation status of transaxle control cable and
transmission range switch.
Q:Is the check result normal?
YES:
Go to Step 2.
NO:
Adjust the installation status of transaxle control
cable and transmission range switch. P.23A-157.
STEP 2. Check the transmission fluid.
Check the transmission fluid for burning, fouling, and foreign
material.
Q:Is the check result normal?
YES:
Go to Step 3.
NO:
Go to Step 7.
STEP 3. Check the transmission fluid level.
Check if the transmission fluid level is adequate.
Q:Is the check result normal?
YES:
Go to Step 4.
NO:
Check and repair the leakage point of the
transmission fluid, add the transmission fluid, and then
go to Step 4.
STEP 4. Perform a hydraulic test.
Refer to P.23A-21.
Q:Is the check result normal?
YES:
Go to Step 5.
NO:
Go to Step 7.
STEP 5. Replace the TCM.
Q:Is the failure resolved?
YES:
Go to Step 6.
NO:
Go to Step 7.
STEP 6. Compare with another same model vehicle.
Q:Is there a difference from the same model vehicle?
YES:
Go to Step 7.
NO:
The procedure is complete.
STEP 7. Remove the transaxle assembly from the vehicle.
Disassemble and check the transaxle assembly to check if there
is a foreign material inside.
Q:Is the check result satisfactory?
YES:
Replace the transaxle assembly.
NO:
Replace the failure part.
AUTOMATIC TRANSAXLE MECHANICAL
23A-133
AUTOMATIC TRANSAXLE DIAGNOSIS
INSPECTION PROCEDURE 9: The shift shock is large at a certain gear shift. (1st to 2nd,
2nd to 3rd, etc.)
M12301000447USA0000010000
TROUBLESHOOTING HINTS (THE MOST LIKELY
CAUSES FOR THIS CONDITION:)
⦆
Malfunction of the engine: Engine output change
⦆
Malfunction of the TCM
⦆
A/T failure: Hydraulic system (valve body
assembly), driving force transmission system
(clutch/brake)
NOTE:
When the engine output is low, shock
occurs. Care must also be taken during cold, after
warm up, and temperature, humidity, and air
pressure differences.
DIAGNOSIS
STEP 1. Check the engine performance.
⦆
Check the ECM side especially for throttle signal-related
abnormality.
⦆
Check the stall speed (refer to P.23A-21). If the speed is low,
check the engine side.
Q:Is the check result normal?
YES:
Go to Step 2.
NO:
Repair the failure, and perform adjustment.
STEP 2. Replace the TCM.
Q:Is the failure resolved?
YES:
The procedure is complete.
NO:
Go to Step 3.
STEP 3. Perform a hydraulic test.
Refer to P.23A-21.
Q:Is the check result normal?
YES:
The procedure is complete.
NO:
Go to Step 4.
STEP 4. Compare with another same model vehicle.
Q:Is there a difference from the same model vehicle?
YES:
Go to Step 5.
NO:
The procedure is complete.
STEP 5. Remove the transaxle assembly from the vehicle.
Disassemble and check the transaxle assembly to check if there
is a foreign material inside.
Q:Is the check result satisfactory?
YES:
Replace the transaxle assembly.
NO:
Replace the failure part.
23A-134
AUTOMATIC TRANSAXLE MECHANICAL
AUTOMATIC TRANSAXLE DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст