Mitsubishi Outlander XL. Manual — part 975
YES<Set to the A/T.>:
Troubleshoot the A/T. Refer to
GROUP 23A, Diagnosis P.23A-22.
YES<Set to the AWD.>:
Troubleshoot the AWD. Refer to
YES<Set to the ABS.>:
Troubleshoot the ABS. Refer to
YES<Set to the ASC.>:
Troubleshoot the ASC. Refer to
GROUP 35C, Diagnosis P.35C-11.
YES<Set to the WCM.>:
Troubleshoot the WCM. Refer to
GROUP 42C, diagnosis P.42C-11.
YES<Set to the KOS.>:
Troubleshoot the KOS. Refer to
GROUP 42B, Diagnosis P.42B-18.
YES<Set to the SRS.>:
Troubleshoot the SRS. Refer to
GROUP 52B, Diagnosis P.52B-33.
YES<Set to the ETACS.>:
Troubleshoot the ETACS. Refer
to GROUP 54Ad, Diagnosis P.54Ad-8.
YES<Set to the A/C.>:
Troubleshoot the A/C. Refer to
GROUP 55A, Manual A/C Diagnosis P.55A-8or GROUP 55B,
Automatic A/C Diagnosis P.55B-7.
NO<The diagnosis code is not set.>:
Go to Step 4.
STEP 4. Using scan tool MB991958, check actuator test.
(1)
Turn the ignition switch to the "ON" position.
(2)
Conduct the actuator test of the combination meter.
⦆
Item 7: Indicator1
⦆
Item 8: Indicator2
⦆
Item 9: Indicator3
⦆
Item 10: Indicator4
⦆
Item 11: Shift indicator
⦆
Perform the actuator test, and check that display lights
or warning lights are illuminated normally, or multi
information display is displayed normally.
(3)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the check result normal?
YES:
Go to Step 5.
NO:
Replace the combination meter.
STEP 5. Retest the system.
Check that display lights or warning lights are illuminated
normally, or multi information display is displayed normally.
Q:Is the check result normal?
YES:
The trouble can be an intermittent malfunction
(Refer to GROUP 00 - How to use Troubleshooting/
inspection Service Points - How to Cope with Intermittent
Malfunction P.00-15).
NO:
Replace the combination meter.
COMBINATION METER
54Ab-53
DIAGNOSIS
Inspection Procedure 6: The multi information display screen cannot be changed with
the operation of the meter information switch.
M15410100080USA0000010000
Meter Information Switch Circuit
INTERFACE
CIRCUIT
COMBINATION
METER
CPU
METER
INFOMATION
SWITCH
ZC6008750037
Connectors: C-02, C-03
C-03
C-02
Before replacing the combination meter, be sure
to check that the power supply circuit, earth
circuit, and communication circuit are normal.
TECHNICAL DESCRIPTION (COMMENT)
When the signal from the meter information switch is
received, the combination meter switches the multi
information display screen. If the multi information
display screen does not switch normally, the meter
information switch, wiring harness, connector(s), or
combination meter may have a problem.
TROUBLESHOOTING HINTS
⦆
The meter information switch may be defective
⦆
The combination meter may be defective
⦆
The wiring harness or connectors may have loose,
corroded, or damaged terminals, or terminals
pushed back in the connector
DIAGNOSIS
Required Special Tools:
⦆
MB991223: Harness Set
⦆
MB992006: Extra Fine Probe
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
54Ab-54
COMBINATION METER
DIAGNOSIS
⦆
MB991824: Vehicles Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
STEP 1. Using scan tool MB991958, read the combination
meter diagnostic trouble code.
Check if DTC is set to the combination meter.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958. Refer to "How to connect the
Scan Tool (M.U.T.-III) P.54Ab-5."
(2)
Turn the ignition switch to the "ON" position.
(3)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(4)
Check if DTC is set.
Q:Is the DTC set?
YES:
NO:
Go to Step 2.
STEP 2. Check meter information switch connector C-02 for
loose, corroded or damaged terminals, or terminals pushed
back in the connector.
Q:Is meter information switch connector C-02 in good
condition?
YES:
Go to Step 3.
NO:
Repair the defective connector.
STEP 3. Check the meter information switch.
Check the meter information switch. Refer to P.54Ab-69.
Q:Is the check result normal?
YES:
Go to Step 4.
NO:
Replace the meter information switch.
STEP 4. Check the wiring harness between meter
information switch connector C-02 (terminal 4) and ground.
Q:Is the wiring harness between fuel meter information
switch connector C-02 (terminal 4) and ground in good
condition?
YES:
Go to Step 5.
NO:
Repair the wiring harness.
COMBINATION METER
54Ab-55
DIAGNOSIS
STEP 5. Check combination meter connector C-03 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q:Is combination meter connector C-03 in good condition?
YES:
Go to Step 6.
NO:
Repair the defective connector.
STEP 6. Check the wiring harness between meter
information switch connector C-02 (terminal 1) and
combination meter connector C-03 (terminal 3).
Q:Are the wiring harness between meter information switch
connector C-02 (terminal 1) and combination meter
connector C-03 (terminal 3) in good condition?
YES:
Go to Step 7.
NO:
Repair the wiring harness.
STEP 7. Retest the system.
Check that the multi information display screen switches
normally when the meter information switch is operated.
Q:Is the check result normal?
YES:
The trouble can be an intermittent malfunction
(Refer to GROUP 00 - How to use Troubleshooting/
inspection Service Points - How to Cope with Intermittent
Malfunction P.00-15).
NO:
Replace the combination meter.
SERVICE DATA
M15410100034USA0000010000
NOTE:
Some items are not displayed on M.U.T.-III
according to the information in the ECU.
Item No. Scan tool MB991958 display
Condition
01
Illumination
ON or OFF
02
Outside temperature
°C or °F
03
Frost warning indicator
ON or OFF
04
Engine coolant temp. lamp(HOT)
ON or OFF
05
Immobilizer indicator
ON or OFF
06
Oil level indicator
ON or OFF
07
4WD failure indicator
ON or OFF
08
Hood indicator
ON or OFF
09
Washer fluid level warning
ON or OFF
23
A/T failure indicator(Symbol)
ON or OFF
24
Air purifier indicator
ON or OFF
25
ASC/TCL failure indicator
ON or OFF
26
Key reminder indicator
ON or OFF
27
Head lamp reminder indicator
ON or OFF
28
Brake reminder indicator
ON or OFF
54Ab-56
COMBINATION METER
DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст