Mitsubishi Outlander XL. Manual — part 960

ZC500483

Tires
without
wheels

Seat belt

Deployment
wires

0000

6.

Pull the seat belt out to the outside of the tire, and then place
one tire without a wheel on top.

ZC500488

Deployment wires

Vehicle battery

0000

｠

Before operation, check carefully to be sure that no one
is nearby.

｠

The inflator will be quite hot immediately following the
operation, so wait at least 30 minutes to allow it to cool
before attempting to handle it. Although not poisonous,
do not inhale gas from seat belt pre-tensioner operation.
See Deployed Air Bag Module and Operated Seat Belt pre-
tensioner Disposal (Refer to P.52B-371) for post-
operation handling instructions.

｠

If the seat belt pre-tensioner fails to operate, do not go
near the seat belt pre-tensioner.

7.

At a location as far away from the air bag module as possible,
and from a shielded position, disconnect the two connected
wires from each other, and connect them to the two terminals
of the battery (which has been removed from the vehicle) to
operate the seat belt pre-tensioner.

8.

Discard the operated seat belt pre-tensioner as specified in
Deployed Air Bag Module and Seat Belt pre-tensioner
Disposal (Refer to P.52B-371).

DEPLOYED AIR BAG MODULE AND OPERATED

SEAT BELT PRE-TENSIONER DISPOSAL

After deployment and operation, the air bag module and seat
belt pre-tensioner should be disposed of in the same manner as
any other scrap parts, adhering to local laws and/or legislation.
Observe the following precautions during air bag or seat belt pre-
tensioner disposal:

1.

The inflator will be quite hot immediately following
deployment, so wait at least 30 minutes to allow it cool before
attempting to handle it.

2.

Do not put water or oil on the air bag after deployment or on
the seat belt pre-tensioner after operation.

If after following these precautions, any material does get
into the eyes or on the skin, immediately rinse the affected
area with a large amount of clean water. If any irritation
develops, seek medical attention.

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

52B-371

AIR BAG MODULE AND SEAT BELT PRE-TENSIONER DISPOSAL PROCEDURES

3.

There may be material on the deployed air bag module or the
operated seat belt pre-tensioner, that could irritate the eye
and/or skin. Wear gloves and safety glasses when handling a
deployed air bag module or the operated seat belt pre-
tensioner.

ZC600288

Air bag module and
seat belt pre-tensioner

Strong plastic bag

0000

4.

Tightly seal the air bag module and seat belt pre-tensioner in
a strong plastic bag for disposal.

5.

Be sure to always wash your hands after completing this
operation.

52B-372

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

AIR BAG MODULE AND SEAT BELT PRE-TENSIONER DISPOSAL PROCEDURES

GROUP 54Aa

BATTERY

CONTENTS

ON-VEHICLE SERVICE. . ....

54Aa-2

BATTERY CHECK. . . . .

54Aa-2

BATTERY CHARGING. . . ..

54Aa-3

BATTERY TEST. . . . ..

54Aa-3

REMOVAL AND INSTALLATION. ..

54Aa-5

54Aa-1

ON-VEHICLE SERVICE

BATTERY CHECK

M15401000904USA0000010000

Battery posts, terminals and related accessories contain
lead and lead compounds. WASH HANDS AFTER
HANDLING.

BATTERY VISUAL INSPECTION (1)

ZC5019960000

Indicator

Blue

Charging
necessary

Good
condition

White

The battery contains a visual test indicator which gives a blue
signal when an adequate charge level exists, and a white signal
when charging is required.

BATTERY VISUAL INSPECTION (2)
Make sure the ignition switch is in "LOCK" (OFF) position and
all battery fed accessories are OFF.

1.

Disconnect the negative cable from battery before
disconnecting the positive cable.

Care should be taken in the event battery case is cracked
or leaking to protect hands from the electrolyte. A suitable
pair of rubber gloves (not the household type) should be
worn when removing battery by hand.

2.

Remove the battery from the vehicle.

54Aa-2

BATTERY

ON-VEHICLE SERVICE