Mitsubishi Outlander XL. Manual — part 759
NO:
Repair or replace the damaged component(s). Refer to
GROUP 00E, Harness Connector Inspection P.00E-2. Check
that the sunroof works normally.
STEP 3. Sunroof switch check
(1)
Remove the sunroof switch. Refer to P.42Ad-41.
ZC6001270000
Sunroof switch
(2)
Check continuity when the sunroof switch is operated to
"TILT-UP" position.
Switch
position
Terminal No.
Normal value
Tilt-up
3 - 4
Continuity
exists (2 Ω or
less)
OFF
3 - 4, 4 - 5, 4 - 6 Open circuit
Q:Is the sunroof switch normal?
YES:
Go to Step 4.
NO:
Replace the sunroof switch. Check that the sunroof
works normally.
STEP 4. Check sunroof motor assembly connector D-04 for
loose, corroded or damaged terminals, or terminals pushed
back in the connector.
Q:Is sunroof motor assembly connector D-04 in good
condition?
YES:
Go to Step 5.
NO:
Repair or replace the damaged component(s). Refer to
GROUP 00E, Harness Connector Inspection P.00E-2. Check
that the sunroof works normally.
STEP 5. Check the wiring harness between sunroof switch
connector D-03 (terminal 3) and sunroof motor assembly
connector D-04 (terminal 4).
Q:Is the wiring harness between sunroof switch connector
D-03 (terminal 3) and sunroof motor assembly connector
D-04 (terminal No. 4) in good condition?
YES:
Go to Step 6.
NO:
The wiring harness may be damaged or the connector
(s) may have loose, corroded or damaged terminals, or
terminals pushed back in the connector. Repair the wiring
harness as necessary. Check that the sunroof works
normally.
STEP 6. Retest the system.
Check that the sunroof lid glass tilts up.
Q:Is the check result normal?
YES:
No action is necessary and testing is complete.
NO:
Replace the sunroof motor assembly. Check that the
sunroof works normally.
SUNROOF
42Ad-23
SUNROOF DIAGNOSIS
INSPECTION PROCEDURE 3: The Sunroof Lid Glass does not Open (Tilt-up, Tilt-down
and Close Normally).
M14206000048USA0000010000
Before replacing the ECU, ensure that the power
supply circuit, the ground circuit and the
communication circuit are normal.
ZC600615
CPU
SUNROOF
SWITCH
INPUT CIRCUIT
INPUT CIRCUIT
DRIVE CIRCUIT
SUNROOF MOTOR
HALL SENSOR
SUNROOF
MOTOR
ASSEMBLY
BLA
CK
BLA
CK
BLUE
YELLO
W
GREEN
Sunroof Switch Circuit
0000
42Ad-24
SUNROOF
SUNROOF DIAGNOSIS
ZC600879
Connectors: D-03, D-04
D-04 (GR)
D-03 (B)
0007
TECHNICAL DESCRIPTION (COMMENT)
The sunroof switch or the sunroof motor assembly
may be defective.
TROUBLESHOOTING HINTS
⦆
The sunroof switch may be defective
⦆
The sunroof motor assembly may be defective
⦆
The wiring harness or connectors may have loose,
corroded, or damaged terminals, or terminals
pushed back in the connector
DIAGNOSTIC PROCEDURE
Required Special Tools:
⦆
MB992006: Extra fine probe
⦆
MB991223: Harness set
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicles Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
STEP 1. Using scan tool MB991958, read the diagnostic
trouble code.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958. Refer to GROUP 54Ad, "How
to connect scan tool (M.U.T.-III) P.54Af-4."
(2)
Turn the ignition switch to the "ON" position.
(3)
Check whether the ETACS-ECU related DTC is set.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the DTC set?
YES:
Diagnose the ETACS-ECU. Refer to P.42Ad-4.
NO:
Go to Step 2.
STEP 2. Check sunroof switch connector D-03 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q:Is sunroof switch connector D-03 in good condition?
YES:
Go to Step 3.
SUNROOF
42Ad-25
SUNROOF DIAGNOSIS
NO:
Repair or replace the damaged component(s). Refer to
GROUP 00E, Harness Connector Inspection P.00E-2. Check
that the sunroof works normally.
STEP 3. Sunroof switch check
(1)
Remove the sunroof switch. Refer to P.42Ad-41.
ZC6001270000
Sunroof switch
(2)
Check continuity when the sunroof switch is operated to
"OPEN" position.
Switch
position
Terminal No.
Normal value
Open
4 - 5
Continuity
exists (2 Ω or
less)
OFF
3 - 4, 4 - 5, 4 - 6 Open circuit
Q:Is the sunroof switch normal?
YES:
Go to Step 4.
NO:
Replace the sunroof switch.
STEP 4. Check sunroof motor assembly connector D-04 for
loose, corroded or damaged terminals, or terminals pushed
back in the connector.
Q:Is sunroof motor assembly connector D-04 in good
condition?
YES:
Go to Step 5.
NO:
Repair or replace the damaged component(s). Refer to
GROUP 00E, Harness Connector Inspection P.00E-2. Check
that the sunroof works normally.
STEP 5. Check the wiring harness between sunroof switch
connector D-03 (terminal 5) and sunroof motor assembly
connector D-04 (terminal 5).
Q:Is the wiring harness between sunroof switch connector
D-03 (terminal 5) and sunroof motor assembly connector
D-04 (terminal No. 5) in good condition?
YES:
Go to Step 6.
NO:
The wiring harness may be damaged or the connector
(s) may have loose, corroded or damaged terminals, or
terminals pushed back in the connector. Repair the wiring
harness as necessary. Check that the sunroof works
normally.
STEP 6. Retest the system.
Check that the sunroof lid glass opens.
Q:Is the check result normal?
YES:
No action is necessary and testing is complete.
NO:
Replace the sunroof motor assembly. Check that the
sunroof works normally.
42Ad-26
SUNROOF
SUNROOF DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст