Mitsubishi Outlander XL. Manual — part 829
STEP 2. Using scan tool MB991958, read the diagnostic
trouble code.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958. Refer to "How to connect scan
tool (M.U.T.-III) P.42C-7."
(2)
Turn the ignition switch to the "ON" position.
(3)
Check whether the ETACS-ECU related DTC is set.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the DTC set?
YES:
Diagnose the ETACS-ECU. Refer to GROUP 54Ad, P.
NO:
Go to Step 3.
STEP 3. Check the power supply system
With the ignition switch in the LOCK (OFF) position, check if the
following function operates normally:
⦆
Hazard warning light
Q:Is the check result normal?
YES:
Go to Step 4.
NO:
Refer to GROUP 54Ad, Malfunction of ETACS-ECU power
STEP 4. Verify the central door locking system.
Q:Does the central door locking system work normally?
YES:
Go to Step 5.
NO:
Refer to GROUP 42Ab, Trouble Symptom Chart P.
STEP 5. Using scan tool MB991958, check data list.
Check the signals related to the keyless entry system operation.
WIRELESS CONTROL MODULE (WCM)
42C-75
DIAGNOSIS
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958. Refer to "How to connect the
Scan Tool (M.U.T.-III) P.42C-7."
(2)
Turn the ignition switch to the "ON" position.
(3)
Check the ETACS data list.
⦆
Turn the ignition switch to the LOCK (OFF) position.
⦆
Close the driver's door.
⦆
Close the passenger's door.
⦆
Close the RH-side rear door.
⦆
Close the LH-side rear door.
⦆
Close the liftgate.
⦆
Remove the ignition key from the ignition key cylinder.
Item No.
Item name
Normal
condition
Item 254
IG voltage
Battery
voltage
Item 256
Dr door ajar switch
Close
Item 257
As door ajar switch
Close
Item 258
RR door ajar switch Close
Item 259
RL door ajar switch
Close
Item 260
Trunk/gate trunk ajar
switch
Close
Item 264
Handle lock switch
Key in → Key
out
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
OK: Normal condition is displayed.
Q:Is the check result normal?
YES (Normal conditions are displayed for all the items.):
Go to Step 6.
NO (Normal condition is not displayed for item No.
254.):
Refer to GROUP 54Ad, Inspection Procedure 2: ETACS-
ECU does not receive any signal from the ignition switch
(IG1) P.54Ad-62.
NO (Normal condition is not displayed for item No.
256.):
Refer to GROUP 54Ad, Inspection Procedure 5: ETACS-
ECU does not receive any signal from the front door switch
(LH) P.54Ad-73.
NO (Normal condition is not displayed for item No.
257.):
Refer to GROUP 54Ad, Inspection Procedure 6: ETACS-
ECU does not receive any signal from the front door switch
(RH) P.54Ad-75.
NO (Normal condition is not displayed for item No.
258.):
Refer to GROUP 54Ad, Inspection Procedure 8: ETACS-
ECU does not receive any signal from the rear door switch
(RH) P.54Ad-80.
42C-76
WIRELESS CONTROL MODULE (WCM)
DIAGNOSIS
NO (Normal condition is not displayed for item No.
259.):
Refer to GROUP 54Ad, Inspection Procedure 7: ETACS-
ECU does not receive any signal from the rear door switch
(LH) P.54Ad-77.
NO (Normal condition is not displayed for item No.
260.):
Refer to GROUP 54Ad, Inspection Procedure 9: ETACS-
ECU does not receive any signal from the liftgate
switch P.54Ad-82.
NO (Normal condition is not displayed for item No.
264.):
Refer to GROUP 54Ad, Inspection Procedure 3: ETACS-
ECU does not receive any signal from the key reminder
switch. P.54Ad-64.
STEP 6. Using scan tool MB991958, check pulse check.
Check the signals related to the keyless entry system operation.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958. Refer to "How to connect the
Scan Tool (M.U.T.-III) P.42C-7."
(2)
Confirm the ETACS pulse check.
⦆
Remove the ignition key from the ignition key cylinder.
Item name
Conditions
Transmitter switch
Turn the switch ON/OFF.
OK: The scan tool (M.U.T.-III) tone alarm sounds.
Q:Is the check result normal?
YES:
Go to Step 7.
NO:
STEP 7. Retest the system.
Check if the keyless entry system works normally.
Q:Is the check result normal?
YES:
Intermittent malfunction (Refer to GROUP 00 - How
to Use Troubleshooting/Inspection Service Points - How to
Cope with Intermittent Malfunction P.00-15).
NO:
Replace WCM and register the ID codes (Refer to P.
WIRELESS CONTROL MODULE (WCM)
42C-77
DIAGNOSIS
INSPECTION PROCEDURE 6: The Dome Light, The Turn-signal Lights The Horn do not
Operate through The Answerback Function.
M14209200040USA0000010000
Before replacing the ECU, ensure that the power supply
circuit, the ground circuit and the communication circuit are
normal.
COMMENTS ON TROUBLE SYMPTOM
If the hazard warning light, the dome light and the horn work
normally, ETACS-ECU may be faulty. Also, the answerback
function may have been disabled using the customization
function.
PROBABLE CAUSES
⦆
Malfunction of the turn signal light
⦆
Malfunction of the dome light
⦆
Malfunction of the horn
⦆
Malfunction of ETACS-ECU
⦆
Damaged wiring harness and connectors
DIAGNOSTIC PROCEDURE
STEP 1. Verify the hazard warning lights.
Check that the hazard warning lights illuminate normally.
Q:Is the check result normal?
YES:
Go to Step 2.
NO:
Refer to GROUP 54Ac, Inspection Procedure 1: The
Hazard Warning lights do not Illuminate P.54Ac-163.
STEP 2. Verify the dome light.
Check that the dome light illuminate normally.
Q:Is the check result normal?
YES:
Go to Step 3.
NO:
Refer to GROUP 54Ac, Trouble Symptom Chart P.
STEP 3. Verify the horn.
Check that the horn normally.
Q:Is the check result normal?
YES:
Go to Step 4.
NO:
Replace the horn (Refer to GROUP 54Af, Horn P.
STEP 4. Check the operation of the keyless entry system.
Operate the transmitter and check that all doors (including the
liftgate) lock and unlock.
Q:Is the check result normal?
42C-78
WIRELESS CONTROL MODULE (WCM)
DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст