Mitsubishi Outlander XL. Manual — part 492
STEP 6. Check the TCM and A/T control solenoid valve
assembly connector pin terminals and the connection
status.
Q:Is the check result normal?
YES:
Replace the TCM.
NO:
Repair or replace the failure section.
STEP 7. Erase the DTC code, and drive the vehicle for a
while.
Check that the normal code is displayed.
Q:Is the check result normal?
YES:
The procedure is complete.
NO:
Return to START.
DTC P0815: Paddle Shift Switch (Up) System
M12301000415USA0000010000
PADDLE
SHIFT
SWITCH
TRANSMISSION
CONTROL
MODULE
ZC602377AA00
Paddle shift switch system circuit
AUTOMATIC TRANSAXLE MECHANICAL
23A-83
AUTOMATIC TRANSAXLE DIAGNOSIS
ZC6008750023
Connector: C-34
C-34 (BR)
ZC6035780002
Connectors: C-37, 38
C-38
C-37
Brake pedal
ZC6008770008
Connector: C-208
DESCRIPTIONS OF MONITOR METHODS
⦆
With the ignition switch ON, the paddle shift switch
(up) status continues for 60 seconds.
TROUBLESHOOTING HINTS (THE MOST LIKELY
CAUSES FOR THIS CODE TO BE SET ARE:)
⦆
Malfunction of the Paddle shift switch (up) system
circuit
⦆
Damaged harness or connector
⦆
Malfunction of the TCM
⦆
Malfunction of the paddle shift switch
DIAGNOSIS
STEP 1. Check the TCM terminal voltage.
[C-38 TCM connector (vehicle side, connected)]
Measure the voltage between C-38 No. 9 and body ground.
⦆
Ignition switch: ON
⦆
Paddle (ON) operated: 1V or less
⦆
Other than above: battery positive voltage
Q:Is the check result normal?
YES:
Go to Step 2.
NO:
Go to Step 3.
STEP 2. Check the TCM connector, vehicle-side wiring
harness connector pin terminal, and the connection status.
Q:Is the check result normal?
YES:
Go to Step 6.
23A-84
AUTOMATIC TRANSAXLE MECHANICAL
AUTOMATIC TRANSAXLE DIAGNOSIS
NO:
Repair or replace the failure section.
STEP 3. Check between the TCM connector and the paddle
shift switch (up).
Check for continuity between C-38 TCM connector terminal No.
9 and C-208 paddle shift switch (up).
⦆
Between C-38 terminal No. 9 and C-208 terminal No. 1:
Continuity exists.
When the continuity check result is OK, check that the wiring
harness is not shorted to the body and other wiring harness.
Q:Is the check result normal?
YES:
Go to Step 4.
NO:
Repair or replace the failure section.
STEP 4. Check the paddle shift switch (up).
Refer to P.23A-161.
Q:Is the check result normal?
YES:
Go to Step 5.
NO:
Repair or replace the failure section.
STEP 5. Check the TCM connector, vehicle-side wiring
harness connector pin terminal, and the connection status.
Q:Is the check result normal?
YES:
Replace the TCM.
NO:
Repair or replace the failure section.
STEP 6. Erase the DTC code, and drive the vehicle for a
while.
Check that the normal code is displayed.
Q:Is the check result normal?
YES:
The procedure is complete.
NO:
Return to START.
DTC P0816: Paddle Shift Switch (Down) System
M12301000416USA0000010000
PADDLE SHIFT SWITCH (DOWN) SYSTEM
CIRCUIT
Refer to P.23A-83.
DESCRIPTIONS OF MONITOR METHODS
⦆
With the ignition switch ON, the paddle shift switch
(down) status continues for 60 seconds.
TROUBLESHOOTING HINTS (THE MOST LIKELY
CAUSES FOR THIS CODE TO BE SET ARE:)
⦆
Malfunction of the Paddle shift switch (down)
system circuit
⦆
Damaged harness or connector
⦆
Malfunction of the TCM
⦆
Malfunction of the paddle shift switch
AUTOMATIC TRANSAXLE MECHANICAL
23A-85
AUTOMATIC TRANSAXLE DIAGNOSIS
DIAGNOSIS
STEP 1. Check the TCM terminal voltage.
[C-38 TCM connector (vehicle side, connected)]
Measure the voltage between C-38 terminal No. 32 and body
ground.
⦆
Ignition switch: ON
⦆
Paddle (ON) operated: 1V or less
⦆
Other than above: battery positive voltage
Q:Is the check result normal?
YES:
Go to Step 2.
NO:
Go to Step 3.
STEP 2. Check the TCM connector, vehicle-side wiring
harness connector pin terminal, and the connection status.
Q:Is the check result normal?
YES:
Go to Step 6.
NO:
Repair or replace the failure section.
STEP 3. Check between the TCM connector and the paddle
shift switch (down).
Check for continuity between C-38 TCM connector and C-208
paddle shift switch (down).
⦆
Between C-38 terminal No. 32 and C-208 terminal No. 3:
Continuity exists.
When the continuity check result is OK, check that the wiring
harness is not shorted to the body and other wiring harness.
Q:Is the check result normal?
YES:
Go to Step 4.
NO:
Repair or replace the failure section.
STEP 4. Check the paddle shift switch (down).
Refer to P.23A-161.
Q:Is the check result normal?
YES:
Go to Step 5.
NO:
Repair or replace the failure section.
STEP 5. Check the TCM connector, vehicle-side wiring
harness connector pin terminal, and the connection status.
Q:Is the check result normal?
YES:
Replace the TCM.
NO:
Repair or replace the failure section.
STEP 6. Erase the DTC code, and drive the vehicle for a
while.
Check that the normal code is displayed.
Q:Is the check result normal?
YES:
The procedure is complete.
NO:
Return to START.
23A-86
AUTOMATIC TRANSAXLE MECHANICAL
AUTOMATIC TRANSAXLE DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст