Mitsubishi Outlander XL. Manual — part 1058
STEP 10. Retest the system
Q:Is the check result normal?
YES:
The trouble can be an intermittent malfunction
(Refer to GROUP 00, How to use Troubleshooting/inspection
Service Points - How to Cope with Intermittent
Malfunction P.00-15).
NO:
Carry out the troubleshooting again.
STEP 11. Check AC outlet connector D-103 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q:Is AC outlet connector D-103 in good condition?
YES:
Go to Step 12.
NO:
Repair the damaged parts.
STEP 12. Measure the resistance at AC inverter connector
D-128 and AC outlet connector D-103.
(1)
Disconnect the connector, and measure at the wiring harness
side.
ZC5013540000
Connector C-128
(Harness side)
Connector D-103
(Harness side)
(2)
Measure the resistance between AC inverter connector
D-128 (terminal No. 4) and AC outlet connector D-103
(terminal No. 3).
⦆
The measured value should be 2 Ω or less.
ACCESSORY
54Ae-11
AC POWER SUPPLY
ZC5013540001
Connector C-128
(Harness side)
Connector D-103
(Harness side)
(3)
Measure the resistance between AC inverter connector
D-128 (terminal No. 11) and AC outlet connector D-103
(terminal No. 1).
⦆
The measured value should be 2 Ω or less.
Q:Does the measured resistance value correspond with this
range?
YES:
Go to Step 14.
NO:
Go to Step 13.
STEP 13. Check the wiring harness between AC inverter
connector D-128 (terminal No. 4,11) and AC outlet
connector D-103 (terminal No. 3,1).
Q:Is the wiring harness between AC inverter connector
D-128 (terminal No. 4,11) and AC outlet connector D-103
(terminal No. 3,1) in good condition?
YES:
Go to Step 14.
NO:
Repair the wiring harness between AC inverter
connector D-128 and AC outlet connector D-103.
STEP 14. Retest the system
Q:After the AC outlet replacement, does the AC power
supply operate normally?
YES:
The trouble can be an intermittent malfunction
(Refer to GROUP 00, How to use Troubleshooting/inspection
Service Points - How to Cope with Intermittent
Malfunction P.00-15).
NO:
Replace the AC inverter.
CHECK AT ECU TERMINALS
M15410400008USA0000010000
D-128
ZC6008700000
54Ae-12
ACCESSORY
AC POWER SUPPLY
Terminal
No.
Check item
Check condition
Normal condition
1
Battery power supply
Always
Battery voltage
3
Ignition switch (IG1) power supply
Ignition switch: ON
Battery voltage
4
AC outlet
Ignition switch: ON
0 V
7
Ground
Always
0 V
11
AC outlet
Ignition switch: ON
0 V
REMOVAL AND INSTALLATION
M15410400010USA0000010000
<AC OUTLET>
ZC3052130000
1
2
Removal Steps
1.
Rear floor console box (Refer to
GROUP 52A, Rear floor Console
Assembly P.52A-9.)
Removal Steps
2.
AC outlet
ACCESSORY
54Ae-13
AC POWER SUPPLY
<AC INVERTER>
ZC6002770000
1
9.0 ± 2.0 N·m
80 ± 17 in-lb
Removal Step
1.
AC inverter
HANDS-FREE CELLULAR PHONE SYSTEM
DIAGNOSIS
STANDARD FLOW OF DIAGNOSTIC TROUBLESHOOTING
M15410400004USA0000010000
Refer to GROUP 00, Troubleshooting contents P.
00-6.
TROUBLE SYMPTOM CHART
M15410400005USA0000010001
Trouble symptom
Inspection
Procedure No.
Reference
page
Hands-free cellular phone system does not work normally.
1
During the conversation with the hands-free system, the speaker’s voice
cannot be heard by the other party.
2
During the conversation with the hands-free system, the voice of other party
cannot be heard.
3
Even when the steering voice-control switch is operated, the conversation is
not possible.
4
The cellular phone is not recognized or the connection cannot be established. 5
Check the hands-free module power supply circuit.
6
54Ae-14
ACCESSORY
HANDS-FREE CELLULAR PHONE SYSTEM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст