Mitsubishi Outlander XL. Manual — part 193
NOTE:
For the vacuum routing, refer to GROUP 17,
Emission Control - Vacuum Hoses - Vacuum Hose
Routing P.17c-5
SPECIFICATION(S)
GENERAL SPECIFICATION(S)
M11301000002USA0000010000
ITEMS
SPECIFICATIONS
Throttle body
Throttle bore mm (in.)
65 (2.56)
Throttle position sensor
Hall element type
Throttle actuator control motor
DC motor type, having brushes
Engine control
module (ECM)
Identification model No.
E6T70475 <Federal-FWD>
E6T70476 <Federal-AWD>
E6T70477 <California-FWD>
E6T70478 <California-AWD>
Sensors
Mass airflow sensor
Heat sensitizing type
Barometric pressure sensor
Semiconductor type
Intake air temperature sensor
Thermistor type
Engine coolant temperature sensor
Thermistor type
Heated oxygen sensor
Zirconia type
Accelerator pedal position sensor
Hall element type
Camshaft position sensor
Magneto resistance element type
Crankshaft position sensor
Magneto resistance element type
Knock sensor
Piezoelectric type
Power steering pressure sensor
Semiconductor type
Manifold absolute pressure sensor
Semiconductor type
Actuators
Multiport fuel injection (MFI) relay
Contact switch type
Fuel pump relay
Contact switch type
Throttle actuator control motor relay
Contact switch type
Injector type and number
Electromagnetic type, 6
Injector identification mark
JLN240B
Engine oil control valve
Duty cycle type solenoid valve
Exhaust gas recirculation (EGR) valve
Stepper motor type
Evaporative emission purge solenoid
Duty cycle type solenoid valve
Intake manifold tuning solenoid
ON/OFF control type solenoid valve
SERVICE SPECIFICATION(S)
M11301000003USA0000010000
ITEMS
STANDARD VALUE
Fuel pressure kPa (psi)
Approximately 324 (47) at curb
idle
MULTIPORT FUEL INJECTION (MFI)
13Aa-7
SPECIFICATION(S)
ITEMS
STANDARD VALUE
Intake air temperature sensor resistance kΩ
-20°C (-4°F)
13 - 17
0°C (32°F)
5.3 - 6.7
20°C (68°F)
2.3 - 3.0
40°C (104°F)
1.0 - 1.5
60°C (140°F)
0.56 - 0.76
80°C (176°F)
0.30 - 0.45
Engine coolant temperature sensor resistance
kΩ
-20°C (-4°F)
14 - 17
0°C (32°F)
5.1 - 6.5
20°C (68°F)
2.1 - 2.7
40°C (104°F)
0.9 - 1.3
60°C (140°F)
0.48 - 0.68
80°C (176°F)
0.26 - 0.36
Heated oxygen sensor output voltage V
0.6 - 1.0
Heated oxygen sensor heater resistance Ω
Front
4.5 - 8.0 [at 20°C (68°F)]
Rear, Center exhaust
pipe
11 - 18 [at 20°C (68°F)]
Injector coil resistance Ω
10.5 - 13.5 [at 20°C (68°F)]
Throttle actuator control motor coil resistance Ω
0.3 - 80 [at 20°C (68°F)]
Engine oil control valve coil resistance Ω
6.9 - 7.9 [at 20°C (68°F)]
SEALANT AND ADHESIVE
M11301000005USA0000010000
ITEM
SPECIFIED SEALANT
Engine coolant temperature sensor threaded portion 3M™ AAD part number 8731or equivalent
13Aa-8
MULTIPORT FUEL INJECTION (MFI)
SPECIFICATION(S)
SPECIAL TOOLS
M11301000006USA0000010000
TOOL
TOOL
NUMBER
AND
NAME
SUPERSESSION
APPLICATION
YB991958
MB991910
MB991826
MB991911
MB991914
MB991824
MB991827
MB991825
a
b
c
d
e
f
g
AA00
Do not use
Do not use
MB991958
A: MB991824
B: MB991827
C: MB991910
D: MB991911
E: MB991914
F: MB991825
G: MB991826
M.U.T.-III sub assembly
A: Vehicle Communication
Interface (V.C.I.)
B: M.U.T.-III USB Cable
C: M.U.T.-III Main Harness A
(Vehicles
with
CAN
communication system)
D: M.U.T.-III Main Harness B
(Vehicles
without
CAN
communication system)
E: M.U.T.-III Main Harness C
(for Daimler Chrysler models
only)
F: M.U.T.-III Measurement
Adapter
G: M.U.T.-III Trigger Harness
MB991824-KIT
NOTE:
G: MB991826
M.U.T.-III Trigger
Harness is not
necessary when
pushing V.C.I. ENTER
key.
⦆
Reading
diagnostic
trouble code
⦆
MFl system inspection
⦆
Measurement
of
fuel
pressure
For vehicles with CAN
communication,
use
M.U.T.-III main harness A
to send simulated vehicle
speed. If you connect
M.U.T.-III main harness B
instead,
the
CAN
communication does not
function correctly.
YB992110AA00
MB992110
Power plant ECU check
harness
-
⦆
lnspection
using
an
oscilloscope
⦆
lnspection of the engine
control module (ECM)
terminal voltage check
MULTIPORT FUEL INJECTION (MFI)
13Aa-9
SPECIAL TOOLS
TOOL
TOOL
NUMBER
AND
NAME
SUPERSESSION
APPLICATION
MB991709
Test harness set
MB991709-01
Inspection
using
an
oscilloscope
MB991658
MB991658
Test harness set
Tool not available
⦆
Inspection
using
an
oscilloscope
⦆
Adjustment of accelerator
pedal position sensor
⦆
Inspection
of
heated
oxygen sensor
MD998464
Test harness (4 pin, square)
MD998464-01
Inspection of heated oxygen
sensor
MB991316
Test harness (4 pin, square)
Tool not available
Inspection of heated oxygen
sensor
MB992049
MB992049
MB992049-01
Measurement
of
fuel
pressure
MB992001
MB992001
MB992049-01
Measurement
of
fuel
pressure
MB991981
MB991981
Fuel pressure gauge set
Tool not available
Measurement
of
fuel
pressure
MB992076
MB992076
Injector test set
Measurement
of
fuel
pressure
YB992106AA00
MB992106
O-ring installer
-
Installation of O-ring on
injector injection nozzle side
13Aa-10
MULTIPORT FUEL INJECTION (MFI)
SPECIAL TOOLS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст