Mitsubishi Outlander XL. Manual — part 464

M.U.T.-III
scan

tool

display

Item
num
ber

Inspection item

Inspection requirement

Normal condition

Vehicle
speed sensor

4

Vehicle speed signal

Road test the vehicle

The speedometer
and

scan

tool

MB991958 display
the same value.

ECM TERMINAL VOLTAGE REFERENCE CHART FOR AUTO-CRUISE CONTROL

SYSTEM OPERATION

M11702000903USA0000010000

1.

Disconnect all ECM connectors, and connect
special tool MB992110 (Power plant ECU check
harness) in between.

2.

Measure the voltages between the check connector
terminals of special tool MB992110 and ground
terminals 81 or 93.

ZC6022260000

Special tool - Power plant ECU check harness (MB992110) connector: Component side

48-Pin connector
(ECM connector B-11)

64-Pin connector
(ECM connector B-10)

Terminal
number

Check item

Check condition

Normal condition

10

Throttle

position

sensor (main)

｠

Remove the intake air hose
at the throttle body

｠

Disconnect the throttle
position sensor, and then
connect terminals 3, 4, 5
and 6 with the use of the
special tool: MB991658.

｠

Ignition switch: "ON"

Fully close the
throttle

valve

with your finger

0.3 - 0.7 V

Fully open the
throttle

valve

with your finger

4.0 V or more

11

Throttle

position

sensor (sub)

｠

Remove the intake air hose
at the throttle body

｠

Disconnect the throttle
position sensor, and then
connect terminals 3, 4, 5
and 6 with the use of the
special tool: MB991658
(Test harness).

｠

Ignition switch: "ON"

Fully close the
throttle

valve

with your finger

2.2 - 2.8 V

Fully open the
throttle

valve

with your finger

4.0 V or more

12

Power supply voltage
applied to throttle
position sensor

Ignition switch: "ON"

4.9 - 5.1 V

AUTO-CRUISE CONTROL SYSTEM

17b-49

AUTO-CRUISE CONTROL SYSTEM DIAGNOSIS

Terminal
number

Check item

Check condition

Normal condition

15

Throttle

actuator

control motor (+)

｠

Ignition switch: "ON"

｠

Accelerator pedal: fully opened to fully closed

Decreases

slightly

(approx. 2 V) from
battery voltage.

16

Throttle

actuator

control motor (-)

｠

Ignition switch: "ON"

｠

Accelerator pedal: fully closed to fully opened

Decreases

slightly

(approx. 2 V) from
battery voltage.

74

Accelerator

pedal

position sensor (main)

Ignition
switch:
"ON"

Release the accelerator pedal

0.735 - 1.335 V

Depress the accelerator pedal.

4.0 V or more

76

Power supply voltage
applied to accelerator
pedal position sensor
(main)

Ignition switch: "ON"

4.9 - 5.1 V

77

Accelerator

pedal

position sensor (sub)

Ignition
switch:
"ON"

Release the accelerator pedal

0.435 - 1.035 V

Depress the accelerator pedal.

3.7 V or more

78

Power supply voltage
applied to accelerator
pedal position sensor
(sub)

Ignition switch: "ON"

4.9 - 5.1 V

107

Auto-cruise

control

switch power supply

Ignition
switch:
"ON"

All switches: OFF

4.7 - 5.0 V

"ON/OFF" switch: "ON"

0 - 0.5 V

"CANCEL" switch: ON

1.0 - 1.8 V

"COAST/SET" switch: ON

2.3 - 3.0 V

"ACC/RES" switch: ON

3.5 - 4.2 V

108

Stoplight

switch

(brake switch)

Ignition
switch:
"ON"

Depress the brake pedal.

Battery

positive

voltage

Release the brake pedal.

1V or less

17b-50

AUTO-CRUISE CONTROL SYSTEM

AUTO-CRUISE CONTROL SYSTEM DIAGNOSIS

SPECIAL TOOLS

M11702000006USA0000010000

Tool

Tool number and name Supersession

Application

MB991910

MB991826

MB991911

MB991914

MB991824

MB991827

MB991825

Do not use

A

B

C

D

E

F

G

Do not use

YB9919580001

MB991958

A: MB991824
B: MB991827
C: MB991910
D: MB991911
E: MB991914
F: MB991825
G: MB991826

M.U.T.-III sub assembly

A:

Vehicle

communication
interface (V.C.I.)
B: M.U.T.-III USB cable
C:

M.U.T.-III

main

harness A (Vehicles
with

CAN

communication system)
D:

M.U.T.-III

main

harness B (Vehicles
without

CAN

communication system)
E:

M.U.T.-III

main

harness C (for Daimler
Chrysler models only)
F: M.U.T.-III adapter
harness
G: M.U.T.-III trigger
harness

MB991824-KIT

NOTE:

G: MB991826

M.U.T.-III trigger
harness is not necessary
when pushing V.C.I.
ENTER key.

For vehicles with CAN
communication,

use

M.U.T.-III main harness
A to send simulated
vehicle speed. If you
connect M.U.T.-III main
harness B or C instead,
the

CAN

communication

does

not function correctly.
Checking data list

AUTO-CRUISE CONTROL SYSTEM

17b-51

SPECIAL TOOLS

Tool

Tool number and name Supersession

Application

YB9912230001

A

D

C

B

Do not use

MB991223

A: MB991219
B: MB991220
C: MB991221
D: MB991222

Harness set

A: Test harness
B: LED harness
C:

LED

harness

adaptor
D: Probe

General service tools

Checking the continuity
and

measuring

the

voltage at the harness
connector

MB992006

YB992006AA01

MB992006
Extra fine probe

General service tool

Continuity check and
voltage measurement at
harness wire or connector
for loose, corroded or
damaged terminals, or
terminals pushed back in
the connector.

YB992110AA00

MB992110
Power plant ECU check
harness

-

Measuring the terminal
voltage at the ECM

ON-VEHICLE SERVICE

AUTO-CRUISE CONTROL SYSTEM OPERATION

CHECK

M11702000904USA0000010000

AUTO-CRUISE CONTROL MAIN SWITCH CHECK

1.

Turn the ignition switch to the "ON" position.

17b-52

AUTO-CRUISE CONTROL SYSTEM

ON-VEHICLE SERVICE