Mitsubishi Outlander XL. Manual — part 362
STEP 3. Check the trouble symptoms.
(1)
Carry out a test drive with the drive cycle pattern. Refer to
Diagnostic Function - OBD-II Drive Cycle Pattern 17 P.
13Ab-8.
(2)
Check the diagnostic trouble code (DTC).
Q:Is DTC P1238 set?
YES:
Replace the ECM. When the ECM is replaced, register
the ID code. Refer to GROUP 42B, ID Code Registration
Judgment Table <Vehicles with KOS> P.42B-12or GROUP
42C, ID Code Registration Judgment Table <Vehicles with
WCM> P.42C-8. Then go to Step 4.
NO:
It can be assumed that this malfunction is
intermittent. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points - How to Cope
with Intermittent Malfunctions P.00-15.
STEP 4. Test the OBD-II drive cycle.
(1)
Carry out a test drive with the drive cycle pattern. Refer to
Diagnostic Function - OBD-II Drive Cycle Pattern 17 P.
13Ab-8.
(2)
Check the diagnostic trouble code (DTC).
Q:Is DTC P1238 set?
YES:
Replace the troubleshooting.
NO:
The procedure is complete.
DTC P1239: Engine RPM Plausibility
M11310100385USA0000010000
TECHNICAL DESCRIPTION
Compares the actual engine speed calculated from
the crankshaft position sensor signal cycle with the
estimated engine speed calculated from the number
of the crankshaft position sensor signal pulses after a
lapse of the specified time.
MONITOR EXECUTION
Continuous
MONITOR EXECUTION CONDITIONS (Other
monitor and Sensor)
Other Monitor (There is no temporary DTC stored in
memory for the item monitored below)
⦆
Not applicable
Sensor (The sensor below is determined to be
normal)
⦆
Not applicable
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
13Ab-643
DIAGNOSTIC TROUBLE CODE PROCEDURES
DTC SET CONDITIONS
Logic Flow Chart
ZK604066 AA00
Start
End
No
No
No
Yes
Yes
Yes
Yes
No
Malfunction
Good
Continuous
failure for 0.5secs
|Ne (120 )-Ne (10 )|
>= 500rpm
Ne (120 ) >= 500rpm
Ne (10 ) > 1000rpm
Check Condition
⦆
The engine speed monitored with a 120 degree-
cycle pulse is 500 r/min or more.
Judgment Criterion
⦆
The difference between the engine speed
monitored with a 120 degree-cycle pulse and the
engine speed monitored with a 10 degree-cycle
pulse is 500 r/min or more.
Check Condition
⦆
The engine speed monitored with a 120 degree-
cycle pulse is 500 r/min or less.
Judgment Criterion
⦆
The engine speed monitored with a 10 degree-
cycle pulse is 1,000 r/min or more.
OBD-II DRIVE CYCLE PATTERN
Refer to Diagnostic Function - OBD-II Drive Cycle
Pattern 24 P.13Ab-8.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
⦆
Crankshaft position sensor system failed.
⦆
ECM failed.
13Ab-644
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
DIAGNOSTIC TROUBLE CODE PROCEDURES
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: V.C.I.
⦆
MB991827: USB Cable
⦆
MB991910: Main Harness A
STEP 1. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958 to the data link connector.
(2)
Turn the ignition switch to the "ON" position.
(3)
Read the DTC.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the diagnostic trouble code other than P1239 set?
YES:
Refer to, Diagnostic Trouble Code Chart P.13Ab-44.
NO:
Go to Step 2.
STEP 2. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
(1)
Turn the ignition switch to the "ON" position.
(2)
After the DTC has been deleted, read the DTC again.
(3)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is DTC P1239 set?
YES:
Replace the ECM. When the ECM is replaced, register
the ID code. Refer to GROUP 42B, ID Code Registration
Judgment Table <Vehicles with KOS> P.42B-12or GROUP
42C, ID Code Registration Judgment Table <Vehicles with
WCM> P.42C-8. Then go to Step 3.
NO:
It can be assumed that this malfunction is
intermittent. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points - How to Cope
with Intermittent Malfunctions P.00-15.
STEP 3. Test the OBD-II drive cycle.
(1)
Carry out a test drive with the drive cycle pattern. Refer to
Diagnostic Function - OBD-II Drive Cycle Pattern 17 P.
13Ab-8.
(2)
Check the diagnostic trouble code (DTC).
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
13Ab-645
DIAGNOSTIC TROUBLE CODE PROCEDURES
Q:Is DTC P1239 set?
YES:
Retry the troubleshooting.
NO:
The inspection is complete.
DTC P1240: Ignition Angle
M11310100386USA0000010000
TECHNICAL DESCRIPTION
Checks for an abnormal ignition timing retard angle
demand signal from the active stability control (ASC).
DTC SET CONDITIONS
Check Condition
⦆
Ignition switch is "ON" position.
Judgment Criterion
⦆
The ignition timing retard angle demand signal is
not normal.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
⦆
ECM failed.
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: V.C.I.
⦆
MB991827: USB Cable
⦆
MB991910: Main Harness A
STEP 1. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958 to the data link connector.
(2)
Turn the ignition switch to the "ON" position.
(3)
Read the DTC.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the ABS-DTC or ASC-DTC set?
YES:
Refer to GROUP 35B, Anti-lock Braking System -
Diagnostic Trouble Code Chart P.35B-9Refer to GROUP
35C, Active Stability Control System - Diagnostic Trouble
Code Chart P.35C-11.
NO:
Replace the ECM. When the ECM is replaced, register
the ID code. Refer to GROUP 42B, ID Code Registration
Judgment Table <Vehicles with KOS> P.42B-12or GROUP
42C, ID Code Registration Judgment Table <Vehicles with
WCM> P.42C-8.
13Ab-646
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
DIAGNOSTIC TROUBLE CODE PROCEDURES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст