Mitsubishi Outlander XL. Manual — part 1158
ZC6008750010
Connector: C-103
ZC6008760004
Connector: C-111
FUNCTION
If the scan tool MB991958 cannot communicate with
the satellite radio tuner, this diagnosis result will be
set.
TROUBLE JUDGEMENT CONDITIONS
If a communication flag is not set for the satellite radio
tuner, the ETACS-ECU determines that there is a
failure.
TROUBLESHOOTING HINTS
⦆
Malfunction of the connector [joint connector
(CAN1), satellite radio tuner connector improperly
connected]
⦆
Malfunction of the wiring harness [open circuit
between the satellite radio tuner connector and the
joint connector (CAN1), power supply circuit to the
satellite radio tuner]
⦆
Malfunction of the satellite radio tuner
DIAGNOSIS
Required Special Tools:
⦆
MB991223: Harness Set
⦆
MB992006: Extra Fine Probe
STEP 1. Check joint connector (CAN1) C-103 and satellite
radio tuner connector C-111 for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
The strand end of the twisted wire should be within 10 cm
(4 inches) from the connector. For details refer to P.54D-8.
Q:Are joint connector (CAN1) C-103 and satellite radio tuner
connector C-111 in good condition?
YES:
Go to Step 2.
NO:
Repair the damaged parts.
STEP 2. Check the wiring harness between joint connector
(CAN1) C-103 and satellite radio tuner connector C-111.
Strictly observe the specified wiring harness repair
procedure. For details refer to P.54D-8.
(1)
Disconnect joint connector (CAN1) C-103 and satellite radio
tuner connector C-111, and check the wiring harness.
(2)
Check the wiring harness between joint connector (CAN1)
C-103 (terminal No.2) and satellite radio tuner connector
C-111 (terminal No.4)
CONTROLLER AREA NETWORK (CAN)
54D-115
DIAGNOSIS
(3)
Check the wiring harness between joint connector (CAN1)
C-103 (terminal No.13) and satellite radio tuner connector
C-111 (terminal No.11)
Q:Is the wiring harness between joint connector (CAN1)
C-103 and satellite radio tuner connector C-111 in good
condition?
YES:
Check the power supply circuit of the satellite
radio tuner. Refer to Group 54B, Diagnosis <Satellite
radio tuner> P.54B-139.
NO:
Repair the wiring harness between joint connector
(CAN1) C-103 and satellite radio tuner connector C-111.
DIAGNOSTIC ITEM 23: Diagnose when the scan tool cannot receive the data sent by
hands free module.
M15408300033USA0000010000
When servicing a CAN bus line, ground yourself
by touching a metal object such as an unpainted
water pipe. If you fail to do so, a component
connected to the CAN bus line may be damaged.
54D-116
CONTROLLER AREA NETWORK (CAN)
DIAGNOSIS
CAN Communication Circuit
ETACS-ECU
INTERFACE
CIRCUIT
INTERFACE
CIRCUIT
CAN DRIVE
CIRCUIT
HANDS FREE
MODULE
OCCUPANT
CLASSIFICATION-
ECU
SATELLITE
RADIO
TUNER
RADIO AND CD
PLAYER OR CD
CHANGER
NOTE
VEHICLES WITHOUT MITSUBISHI MULTI-COMMUNICATION SYSTEM (MMCS)
VEHICLES WITH MITSUBISHI MULTI-COMMUNICATION SYSTEM (MMCS)
CAN
TRANSCEIVER
CIRCUIT
CAN BOX UNIT
JOINT CONNECTOR
(CAN1)
CONTROLLER AREA NETWORK (CAN)
54D-117
DIAGNOSIS
ZC6008750010
Connector: C-103
ZC6008760005
Connector: C-121
FUNCTION
If the scan tool MB991958 cannot communicate with
the hands free module, this diagnosis result will be
set.
TROUBLE JUDGEMENT CONDITIONS
If a communication flag is not set for the hands free
module, the ETACS-ECU determines that there is a
failure.
TROUBLESHOOTING HINTS
⦆
Malfunction of the connector [joint connector
(CAN1), hands free module connector improperly
connected]
⦆
Malfunction of the wiring harness [open circuit
between the hands free module connector and the
joint connector (CAN1), power supply circuit to the
hands free module]
⦆
Malfunction of the hands free module
DIAGNOSIS
Required Special Tools:
⦆
MB991223: Harness Set
⦆
MB992006: Extra Fine Probe
STEP 1. Check joint connector (CAN1) C-103 and hands free
module connector C-121 for loose, corroded or damaged
terminals, or terminals pushed back in the connector.
The strand end of the twisted wire should be within 10 cm
(4 inches) from the connector. For details refer to P.54D-8.
Q:Are joint connector (CAN1) C-103 and hands free module
connector C-121 in good condition?
YES:
Go to Step 2.
NO:
Repair the damaged parts.
STEP 2. Check the wiring harness between joint connector
(CAN1) C-103 and hands free module connector C-121.
Strictly observe the specified wiring harness repair
procedure. For details refer to P.54D-8.
(1)
Disconnect joint connector (CAN1) C-103 and hands free
module connector C-301, and check the wiring harness.
(2)
Check the wiring harness between joint connector (CAN1)
C-103 (terminal No.7) and hands free module connector
C-121 (terminal No.4)
54D-118
CONTROLLER AREA NETWORK (CAN)
DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст