Mitsubishi Outlander XL. Manual — part 849
STEP 2. Check the ETACS configuration function.
Use the ETACS configuration function to confirm that "FRONT
WIPER OPERATION" is set to "VEHICLE SPEED
DEPENDENT".
Q:Is the check result normal?
YES:
Go to Step 3.
NO:
Use the ETACS configuration function to set "FRONT
WIPER OPERATION" to "VEHICLE SPEED DEPENDENT" (Refer
to P.51B-48).
STEP 3. Use the scan tool MB991958 to diagnose the CAN
bus lines.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
Connect the scan tool. Refer to GROUP 54Ad ETACS,
"Diagnostic function P.54Ad-5."
Q:Is the check result normal?
YES:
Go to Step 4.
NO:
Repair the CAN bus line (Refer to GROUP 54D - CAN bus
STEP 4. Use the scan tool MB991958 to diagnose other
system diagnostic trouble code
Connect the scan tool. Refer to GROUP 54Ad ETACS,
"Diagnostic function P.54Ad-5."
Check that the TCM sets a diagnostic trouble code.
Q:Is the diagnostic trouble code set?
YES:
Diagnose the TCM (Refer to GROUP 23 - Diagnostic
NO:
Go to Step 5.
STEP 5. Retest the system.
Check that the intermittent wiper interval depends on the vehicle
speed.
Q:Is the check result normal?
YES:
Intermittent malfunction. Refer to GROUP 00, How to
cope with intermittent malfunction P.00-15.
NO:
Replace the ETACS-ECU.
WIPER AND WASHER
51B-29
DIAGNOSIS
INSPECTION PROCEDURE 7: The windshield washer does not work.
M15102100014USA0000010001
WINDSHIELD
WASHER
RELAY
REAR
WINDOW
WASHER
RELAY
WASHER
MOTOR
ACC
RELAY3
A-54
ZC603310
WHITE
RED
BLUE-RED
Windshield Washer Motor Circuit
INPUT SIGNAL
(COLUMN-ECU)
WINDSHIELD
WASHER
FUSIBLE
LINK
34
C-309
ETACS-ECU
0000
ZC6008710005
Connector: A-54
ZC6008780022
Connector: C-304
51B-30
WIPER AND WASHER
DIAGNOSIS
ZC600878
Connector: C-309
C-309 (B)
0009
CIRCUIT OPERATION
The windshield washer switch sends a signal through
the column-ECU (incorporated in the column switch)
to the ETACS-ECU. If the column-ECU sends a
windshield washer switch "ON" signal to the ETACS-
ECU, the ETACS-ECU turns on the relay
(incorporated in the ETACS-ECU), thus causing the
washer motor to be turned on.
TECHNICAL DESCRIPTION (COMMENT)
If the windshield washer does not work normally, the
washer motor, the column switch (windshield wiper
and washer switch) or the ETACS-ECU may be
defective.
TROUBLESHOOTING HINTS
⦆
The wiring harness or connectors may have loose,
corroded, or damaged terminals, or terminals
pushed back in the connector
⦆
The washer motor may be defective
⦆
The column switch may be defective
⦆
The ETACS-ECU may be defective
DIAGNOSIS
Required Special Tools:
⦆
MB991223: Harness Set
⦆
MB992006: Extra Fine Probe
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: V.C.I.
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A
STEP 1. Verify the windshield wiper operation.
Q:Does the windshield wiper operate normally?
YES:
Go to Step 2.
NO:
Refer to Inspection Procedure 1 "The windshield
wipers do not work at all P.51B-13."
WIPER AND WASHER
51B-31
DIAGNOSIS
STEP 2. Use the scan tool MB991958 to check if an ETACS-
related diagnostic trouble code is set.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
Connect the scan tool. Refer to GROUP 54Ad ETACS,
"Diagnostic function P.54Ad-5."
Q:Is the diagnostic trouble code set?
YES:
Diagnose the ETACS-ECU. Refer to GROUP 54Ad ETACS,
"Diagnostic trouble code chart P.54Ad-8."
NO:
Go to Step 3.
STEP 3. Check the input signal related to the windshield
washer operation.
⦆
Ignition switch: ACC
⦆
Windshield washer switch: ON
Item No.
Item name
Normal condition
Item 237
Front washer
ON
OK: Normal condition is displayed.
Q:Is the check result normal?
NO:
Go to Step 4.
YES:
Refer to GROUP 54Ad - ETACS, Input signal
STEP 4. Check windshield washer motor connector A-54 for
loose, corroded or damaged terminals, or terminals pushed
back in the connector.
Q:Is windshield washer motor connector A-54 in good
condition?
YES:
Go to Step 5.
NO:
Repair or replace the damaged component(s). Refer to
GROUP 00E, Harness Connector Inspection P.00E-2. Verify
that the windshield wiper works normally.
STEP 5. Check the operation of windshield washer motor.
(1)
Disconnect windshield washer motor connector A-54 and
check at windshield washer motor connector side.
(2)
Fill the windshield washer tank with washer fluid.
51B-32
WIPER AND WASHER
DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст