Mitsubishi Outlander XL. Manual — part 1017
SYMPTOM PROCEDURES
Inspection Procedure 1: The front dome light does not illuminate normally.
M15410900172USA0000010000
Front Dome Light Circuit
ETACS-ECU
FRONT
DOME
LIGHT
ZC6008780004
Connector: C-316
LIGHTING
54Ac-141
DIAGNOSIS
ZC6008790023
Connector: D-02
TROUBLE JUDGMENT
The ETACS-ECU illuminates and extinguishes the
front room light in accordance with the input signals
below.
⦆
Ignition switch (IG1)
⦆
Key reminder switch
⦆
Door switches
⦆
Liftgate latch switch
⦆
Front door lock actuator
TECHNICAL DESCRIPTION (COMMENT)
If this does not work normally, the above switch input
circuit(s), front dome light, or ETACS-ECU may have
a problem.
TROUBLESHOOTING HINTS
⦆
Malfunction of the key reminder switch
⦆
Malfunction of door switch
⦆
Malfunction of liftgate latch switch
⦆
Malfunction of the front door lock actuator
⦆
Malfunction of front dome light
⦆
Malfunction of the ETACS-ECU
⦆
The wiring harness or connectors may have loose,
corroded, or damaged terminals, or terminals
pushed back in the connector
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicle Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
STEP 1. Rear dome light operation check.
Check that the rear dome light illuminates and extinguishes
normally.
Q:Does rear dome light work normally?
YES:
Go to Step 2.
NO:
Replace the ETACS-ECU.
54Ac-142
LIGHTING
DIAGNOSIS
STEP 2. Using scan tool MB991958, read the diagnostic
trouble code.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958. Refer to "How to connect scan
too (M.U.T.-III) P.54Ac-139."
(2)
Turn the ignition switch to the "ON" position.
(3)
Check whether the ETACS-ECU related DTC is set.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the DTC set?
YES:
Diagnose the ETACS-ECU. Refer to GROUP 54Ad,
NO:
Go to Step 3.
STEP 3. Using scan tool MB991958, check data list.
Use the ETACS-ECU data list to check the signals related to the
front dome light.
⦆
Turn the ignition switch to the "LOCK" (OFF) position.
⦆
Remove the ignition key from the ignition key cylinder.
⦆
Open each door.
⦆
Open the liftgate.
Item No.
Item name
Normal
conditions
Item 228
Dr door unlock
ON
Item 254
IG voltage
Battery
voltage
Item 256
Dr door ajar switch
Open
Item 257
As door ajar switch
Open
Item 258
RR door ajar switch Open
Item 259
RL door ajar switch
Open
Item 260
Trunk/gate trunk ajar
switch
Open
Item 264
Handle lock switch
Key in → Key
out
Q:Does scan tool MB991958 display the items "Dr door
unlock", "IG voltage", "Dr door ajar switch", "As door ajar
switch", "RR door ajar switch", "RL door ajar switch",
"Trunk/gate trunk ajar switch" and "Handle lock switch"
as normal condition?
LIGHTING
54Ac-143
DIAGNOSIS
YES<Normal conditions are displayed for all items.>:
Go
to Step 4.
NO<Normal condition is not displayed for item No.
228.>:
Troubleshoot the ETACS-ECU.Refer to GROUP 54Ad,
Diagnosis - Inspection Procedure 4 "ETACS-ECU does not
receive any signal from the front door lock actuator" P.
54Ad-67.
NO<Normal condition is not displayed for item No.
254.>:
Troubleshoot the ETACS-ECU.Refer to GROUP 54Ad,
Diagnosis - Inspection Procedure 4 "ETACS-ECU does not
receive any signal from the ignition switch (IG1)" P.
54Ad-62.
NO<Normal condition is not displayed for item No.
256.>:
Troubleshoot the ETACS-ECU.Refer to GROUP 54Ad,
Diagnosis - Inspection Procedure 5 "ETACS-ECU does not
receive any signal from the front door switch (LH)" P.
54Ad-73.
NO<Normal condition is not displayed for item No.
257.>:
Troubleshoot the ETACS-ECU.Refer to GROUP 54Ad,
Diagnosis - Inspection Procedure 6 "ETACS-ECU does not
receive any signal from the front door switch (RH)" P.
54Ad-75.
NO<Normal condition is not displayed for item No.
258.>:
Troubleshoot the ETACS-ECU.Refer to GROUP 54Ad,
Diagnosis - Inspection Procedure 7 "ETACS-ECU does not
receive any signal from the rear door switch (LH)" P.
54Ad-77.
NO<Normal condition is not displayed for item No.
259.>:
Troubleshoot the ETACS-ECU.Refer to GROUP 54Ad,
Diagnosis - Inspection Procedure 8 "ETACS-ECU does not
receive any signal from the rear door switch (RH)" P.
54Ad-80.
NO<Normal condition is not displayed for item No.
260.>:
Troubleshoot the ETACS-ECU.Refer to GROUP 54Ad,
Diagnosis - Inspection Procedure 9 "ETACS-ECU does not
receive any signal from the liftgate switch" P.
54Ad-82.
NO<Normal condition is not displayed for item No.
264.>:
Troubleshoot the ETACS-ECU.Refer to GROUP 54Ad,
Diagnosis - Inspection Procedure 3 "ETACS-ECU does not
receive any signal from the key reminder switch" P.
54Ad-64.
STEP 4. Check front dome light connector D-02 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q:Is front dome light connector D-02 in good condition?
YES:
Go to Step 5.
NO:
Repair the damaged parts.
STEP 5. Front dome light bulb check
Check that the front dome light bulb is normal.
Q:Does front dome light work normal?
54Ac-144
LIGHTING
DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст