Mitsubishi Outlander XL. Manual — part 766
Parts name
Functional description
Keyless operation key (incorporates
emergency key)
⦆
The keyless operation key receives signals sent from each
interior/exterior transmitter antenna, certifies the keyless
operation key ID code, calculates the encrypted code, and
sends the reply data signal to KOS-ECU via the receiver
antenna module. When the lock/unlock switch on the keyless
operation key is pressed, corresponding signal is sent to KOS-
ECU via the receiver antenna module.
⦆
If two or more keyless operation keys registered in KOS-ECU
respond at the same time, their signals would interfere. To
avoid this interference, each signal from KOS-ECU is given
the priority*1data, and the keyless operation keys respond in
accordance with this priority.
Lock switch
Driver's door
Locks all the doors and the liftgate when a driver carrying the
keyless operation key presses the lock switch on the front door
outside handle or on the liftgate lock release handle.
Front
passenger's
door
Liftgate
Unlock sensor
Driver's door
The unlock sensors incorporated in the driver’s front door
outside handles unlock driver’s the door when a driver carrying
the keyless operation key pulls the driver’s door outside handle.
Front
passenger's
door
The unlock sensors incorporated in the passenger's front door
outside handles unlock all the doors and the liftgate when a
driver carrying the keyless operation key pulls the front door
outside handle.
Liftgate lock release handle
Locks all the doors and the liftgate when a driver carrying the
keyless operation key presses the lock switch on the front door
outside handle or on the liftgate lock release handle.
Exterior transmitter
antenna assembly
Driver's side
Converts the data output from KOS-ECU via wire into a signal,
and sends it to the keyless operation key.
Front
passenger's
side
Interior transmitter
antenna assembly
Front
Converts the data output from KOS-ECU via wire into a signal,
and sends it to the keyless operation key.
Rear
Antenna & tone
alarm assembly
Exterior transmitter
antenna assembly
(liftgate)
Converts the data output from KOS-ECU via wire into a signal,
and sends it to the keyless operation key.
Outer tone alarm
The outer tone alarm sounds when:
⦆
The doors are locked or unlocked by the door entry function.
⦆
The keyless operation key is brought out of the vehicle when
the IG knob is in the "LOCK" (OFF) position and the push
switch is in other than the ON position.
⦆
The lock switch on the keyless operation switch is pressed
when the IG knob is in the "LOCK" (OFF) position and the push
switch is in other than the ON position.
⦆
The lock switch on the keyless operation key is pressed from
inside the car.
⦆
The lock switch on the keyless operation key is pressed when
the door is ajar.
KEYLESS OPERATION SYSTEM (KOS)
42B-7
GENERAL INFORMATION
Parts name
Functional description
Receiver antenna module
Receives the operation signals from the lock/unlock switches
and panic alarm switch on the keyless operation key, and the air
pressure signal from the TPMS transmitter, and then converts
them into data and sends them to KOS-ECU.
TPMS transmitter
Measure tire pressure directly, then send radio frequency signal
to receiver antenna module.
Combination meter (Multi information
display, TPMS warning light)
Communicates with KOS-ECU via CAN. Receives the warning
request or warning information from KOS-ECU, flashes or
activates*2the warning indicator or warnig light. Warning symbol
and message is additionally displayed on the multi information
display
ETACS-ECU
Communicates with KOS-ECU via CAN. Send ignition switch
status. Receives the door lock/unlock request from KOS-ECU,
outputs the lock/unlock signal, and flashes the turn signal light
to inform the driver that the doors are locked/unlocked.
ECM
Communicates with KOS-ECU via CAN. Permits/inhibits the
engine starting and controls the engine operation. Send
atmospheric pressure data.
ABS or ASC-ECU
Communicates with KOS-ECU via CAN. Sends the vehicle
speed data.
NOTE:
*1: When registering the keyless operation
keys, KOS-ECU numbers each key (1 to 4) in the
order they are registered (initial priority). This
priority is renewed each time the doors are
locked/unlocked and the IG knob is pressed. For
example, when only keys 1 and 3 have responded to
the signal sent from KOS-ECU, the new priority of
the keys would be 1-3-2-4. When keys 3 and 4 have
responded, then the priority of the keys becomes
3-4-1-2.
NOTE:
*2: Illuminates for tire pressure warning.
Flashes for about 1 minute and then coutinuously
illuminated for TPMS malfunction warning.
42B-8
KEYLESS OPERATION SYSTEM (KOS)
GENERAL INFORMATION
System configuration
ZC600946
Door lock actuator
ETACS-ECU
Turn-signal light
Steering unit
Push switch
Steering lock unit
Unlock sensor and
lock switch
(driver's side door)
Unlock sensor and
lock switch
(passenger's side door)
Liftgate lock release
handle and lock switch
(liftgate)
Outer buzzer
Receiver antenna module
ECM
Combination meter
(Multi center display, TPMS warning light )
KOS-ECU
Lock switch
Unlock switch
Emergency key (incorporating a transponder)
Indicator light
Radio
frequency
signal
CAN-B
communi-
cation
Front
Rear:
Driver's side
Driver's side
Passenger's side
Liftgate
Rear:
Passenger's side
CAN-C comm-
unication
0001
Liftgate lock actuator
Keyless operation key
Exterior transmitter
antenna assembly
Interior transmitter
antenna assembly
Radio
frequency
signal
Radio
frequency
signal
Radio
frequency
signal
Front tire (LH)
Front tire (RH)
Rear tire (LH)
Rear tire (RH)
TPMS transmitter
CPU
Transmission
circuit
Antenna
Pressure
sensor
Acc.
sensor
Battery
ABS or ASC-ECU
Dome light,
Ignition key cylinder
illumination light
Horn
KEYLESS OPERATION SYSTEM (KOS)
42B-9
GENERAL INFORMATION
SERVICE SPECIFICATIONS
M14209100042USA0000010000
Item
Standard value
Voltage of keyless operation key battery V
2.5 - 3.2
DIAGNOSIS
STANDARD FLOW OF DIAGNOSTIC TROUBLESHOOTING
M14209100044USA0000010000
Refer to GROUP 00 - Contents of troubleshooting P.
00-6.
DIAGNOSTIC FUNCTION
M14209100054USA0000010000
HOW TO CONNECT THE SCAN TOOL (M.U.T.-III)
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicles Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
1.
Ensure that the ignition switch is at the "LOCK" (OFF) position.
2.
Start up the personal computer.
3.
Connect special tool MB991827 to special tool MB991824 and
the personal computer.
4.
Connect special tool MB991910 to special tool MB991824.
5.
Connect special tool MB991910 to the data link connector.
6.
Turn the power switch of special tool MB991824 to the "ON"
position.
NOTE:
When special tool MB991824 is energized, special
tool MB991824 indicator light will be illuminated in a
green color.
7.
Start the M.U.T.-III system on the personal computer.
NOTE:
Disconnecting scan tool MB991958 is the reverse of
the connecting sequence, making sure that the ignition
switch is at the "LOCK" (OFF) position.
42B-10
KEYLESS OPERATION SYSTEM (KOS)
SERVICE SPECIFICATIONS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст