Mitsubishi Outlander XL. Manual — part 386
STEP 1. Replace the DOR radiator.
ZC501967
AC404789
ZC501968
MB991824
MB991827
MB991910
Data link
connector
AA00
(1)
Replace the DOR radiator.
To prevent damage to scan tool MB991958, always turn
the ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(2)
Connect scan tool MB991958 to the data link connector.
(3)
Turn the ignition switch to the "ON" position.
(4)
Read the DTC.
(5)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is DTC P2567 set?
YES:
Replace the ECM. When the ECM is replaced, register
the ID code. Refer to GROUP 42B, ID Code Registration
Judgment Table <Vehicles with KOS> P.42B-12or GROUP
42C, ID Code Registration Judgment Table <Vehicles with
WCM> P.42C-8. Then go to Step 2.
NO:
It can be assumed that this malfunction is
intermittent. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points - How to Cope
with Intermittent Malfunctions P.00-15.
STEP 2. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
(1)
Turn the ignition switch to the "ON" position.
(2)
Read the DTC.
(3)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is DTC P2567 set?
YES:
Repeat the troubleshooting.
NO:
The procedure is complete.
DTC U0001: Bus Off
M11310100397USA0000010000
⦆
If the ECM output the DTC U0001, make sure to
diagnose the CAN bus line.
⦆
Before replacing the ECU, make sure that the
communication circuit is operating normally.
DTC SET CONDITIONS
Check Conditions
⦆
Always
Judgement Criterion
⦆
Bus off error detected
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
⦆
CAN line harness damage or connector damage.
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan tool (M.U.T.-III Sub Assembly)
⦆
MB991824: V.C.I.
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
13Ab-739
DIAGNOSTIC TROUBLE CODE PROCEDURES
⦆
MB991827: USB Cable
⦆
MB991910: Main Harness A
STEP 1. Using scan tool MB991958, diagnose CAN bus line.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting san tool MB991958.
(1)
Connect scan tool MB991958 to the data link connector.
(2)
Turn the ignition switch to the "ON" position.
(3)
Diagnose CAN bus line.
(4)
Turn the ignition switch the "LOCK" (OFF) position.
Q:Is the CAN bus line normal?
YES:
It can be assumed that this malfunction is
intermittent. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points - How to Cope
with Intermittent Malfunctions P.00-15.
NO:
Repair the CAN bus line. Refer to GROUP 54D, Can bus
Diagnostics Table P.54D-10. Then go to Step 2.
STEP 2. Recheck for diagnostic trouble code.
Check again if the DTC is set.
(1)
Erase the DTC.
(2)
Turn the ignition switch to the "ON" position.
(3)
Check if DTC is set.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is DTC U0001 set?
YES:
Retry the troubleshooting.
NO:
The inspection is complete.
DTC U0101: Transmission Control Module Time-Out
M11310100398USA0000010000
⦆
If the ECM output the DTC U0101, make sure to
diagnose the CAN bus line.
⦆
Before replacing the ECU, make sure that the
communication circuit is operating normally.
DESCRIPTIONS OF MONITOR METHODS
There is no data from TCM for the specified time.
(TCM detect communication error with ECM.)
MONITOR EXECUTION
Continuous
MONITOR EXECUTION CONDITIONS (Other
monitor and Sensor)
Other Monitor (There is no temporary DTC stored in
memory for the item monitored below)
⦆
Not applicable
Sensor (The sensor below is determined to be
normal)
⦆
Not applicable
13Ab-740
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
DIAGNOSTIC TROUBLE CODE PROCEDURES
DTC SET CONDITIONS
Check Conditions
⦆
After 4 seconds have passed since the ignition
switch was turned to "ON" position.
⦆
Battery positive voltage is between 10 and 16.5
volts.
Judgement Criterion
⦆
Unable to receive TCM signals through the CAN
bus line 4 seconds.
OBD-II DRIVE CYCLE PATTERN
None.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
⦆
CAN line harness damage or connector damage.
DTC SET CONDITIONS
Logic Flow Chart
Start
End
No
No
Yes
Yes
Yes
No
Malfunction
Continuous Failure
for specified time
Monitoring
Conditions
ZK604051AA00
Communication status
Fails
Good
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan tool (M.U.T.-III Sub Assembly)
⦆
MB991824: V.C.I.
⦆
MB991827: USB Cable
⦆
MB991910: Main Harness A
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
13Ab-741
DIAGNOSTIC TROUBLE CODE PROCEDURES
STEP 1. Using scan tool MB991958, diagnose CAN bus line.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting san tool MB991958.
(1)
Connect scan tool MB991958 to the data link connector.
(2)
Turn the ignition switch to the "ON" position.
(3)
Diagnose CAN bus line.
(4)
Turn the ignition switch the "LOCK" (OFF) position.
Q:Is the CAN bus line normal?
YES:
It can be assumed that this malfunction is
intermittent. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points - How to Cope
with Intermittent Malfunctions P.00-15.
NO:
Repair the CAN bus line. Refer to GROUP 54D, Can bus
Diagnostics Table P.54D-10. Then go to Step 2.
STEP 2. Recheck for diagnostic trouble code.
Check again if the DTC is set.
(1)
Erase the DTC.
(2)
Turn the ignition switch to the "ON" position.
(3)
Check if DTC is set.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is DTC U0101 set?
YES:
Retry the troubleshooting.
NO:
The inspection is complete.
DTC U0114: AWD-ECU Time-Out
M11310100399USA0000010000
⦆
If the ECM output the DTC U0114, make sure to
diagnose the CAN bus line.
⦆
Before replacing the ECU, make sure that the
communication circuit is operating normally.
DTC SET CONDITIONS
Check Conditions
⦆
After 2 seconds have passed since the ignition
switch was turned to "ON" position.
⦆
Battery positive voltage is 10 volts or higher.
Judgement Criterion
⦆
Unable to receive AWD-ECU signals through the
CAN bus line for 4 seconds.
COMMENT
Current Trouble
⦆
Some of the possible causes are a harness or
connector damage between the ECM and the ABS-
ECU/ASC-ECU on the CAN bus line, a failure in the
ABS-ECU/ASC-ECU power supply system, a
failure in the ABS-ECU/ASC-ECU, or a failure in the
ECM.
13Ab-742
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
DIAGNOSTIC TROUBLE CODE PROCEDURES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст