Mitsubishi Outlander XL. Manual — part 1013
⦆
Damaged harness wires and connectors
DIAGNOSIS
Required Special Tools:
⦆
MB991223: Harness Set
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: V.C.I.
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A
STEP 1. Check the fog lights.
When the fog light switch is operated, check that the fog lights
illuminate/go off normally.
Q:Is the fog lights normal?
YES:
Go to Step 2.
NO:
First, repair the front fog lights. Refer to
Inspection Procedure 2 "The right or left fog light does
not illuminate P.54Ac-120."
STEP 2. Using scan tool MB991958, diagnose the CAN bus
line.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958. Refer to "How to connect the
scan tool (M.U.T.-III) P.54Ac-113."
(2)
Turn the ignition switch to the "ON" position.
(3)
Diagnose the CAN bus line.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the CAN bus line found to be normal?
YES:
Go to Step 3.
NO:
Repair the CAN bus line (Refer to GROUP 54D -
STEP 3. Using scan tool MB991958, read the combination
meter diagnostic trouble code.
(1)
Check whether a combination meter-related DTC is set.
(2)
Turn the ignition switch to the "ON" position.
Check whether the combination meter-related DTC is set.
(3)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the DTC set?
YES:
Diagnose the combination meter (Refer to GROUP 54Ab
LIGHTING
54Ac-125
DIAGNOSIS
NO:
Go to Step 4.
STEP 4. Using scan tool MB991958, check actuator test.
(1)
Turn the ignition switch to the "ON" position.
(2)
Perform the actuator test for the combination meter, and
check that the fog light indicator illuminates (Refer to GROUP
54Ab - Diagnosis P.54Ab-61).
(3)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the check result normal?
YES:
Replace the ETACS-ECU.
NO:
Replace the combination meter.
DIAGNOSIS
STANDARD FLOW OF DIAGNOSTIC TROUBLESHOOTING
M15410900005USA0000010006
Refer to GROUP 00 - Contents of troubleshooting P.
00-6.
DIAGNOSTIC FUNCTION
M15410900006USA0000010006
HOW TO CONNECT THE SCAN TOOL (M.U.T.-III)
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicle Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
1.
Ensure that the ignition switch is at the "LOCK" (OFF) position.
2.
Start up the personal computer.
3.
Connect special tool MB991827 to special tool MB991824 and
the personal computer.
4.
Connect special tool MB991910 to special tool MB991824.
5.
Connect special tool MB991910 to the data link connector.
6.
Turn the power switch of special tool MB991824 to the "ON"
position.
NOTE:
When special tool MB991824 is energized, special
tool MB991824 indicator light will be illuminated in a
green color.
7.
Start the M.U.T.-III system on the personal computer.
NOTE:
Disconnecting scan tool MB991958 is the reverse of
the connecting sequence, making sure that the ignition
switch is at the "LOCK" (OFF) position.
54Ac-126
LIGHTING
DIAGNOSIS
HOW TO READ AND ERASE DIAGNOSTIC
TROUBLE CODES
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicle Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
NOTE:
If the battery voltage is low, diagnostic trouble
codes will not be set. Check the battery if scan tool
MB991958 does not display.
1.
Connect scan tool MB991958 to the data link connector.
2.
Turn the ignition switch to the "ON" position.
3.
Select "System select" from the start-up screen.
4.
Select "From 2006 MY" of "Model Year." When the "Vehicle
Information" is displayed, check the contents.
5.
Select "ETACS" from "System List", and press the "OK"
button.
NOTE:
When the "Loading Option Setup" list is displayed,
check the applicable item.
6.
Select "Diagnostic Trouble Code."
7.
If a DTC is set, it is shown.
8.
Choose "Erase DTCs" to erase the DTC.
TROUBLE SYMPTOM CHART
M15410900009USA0000010006
Trouble symptom
Inspection
Procedure No.
Reference
page
Daytime running lights do not illuminate normally. <Vehicles with discharge
headlight>
1
The right or left daytime running light does not illuminate. <Vehicles with
discharge headlight>
2
SYMPTOM PROCEDURES
Inspection Procedure 1: Daytime running lights do not illuminate normally.
M15410900197USA0000010000
Whenever the ECU is replaced, ensure that the input and
output signal circuits are normal.
LIGHTING
54Ac-127
DIAGNOSIS
Daytime Running Light Circuit
FUSIBLE
LINK
36
DAYTIME
RUNNING
LIGHT RELAY
DAYTIME RUNNING
LIGHT
(LH) (RH)
RELAY BOX
ENGINE
COMPARTMENT
ETACS-ECU
54Ac-128
LIGHTING
DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст