Mitsubishi Outlander XL. Manual — part 1081
Tool
Tool number and
name
Supersession
Application
YB9912230000
Do not use
a
b
c
d
MB991223
a.
MB991219
b.
MB991220
c.
MB991221
d.
MB991222
Harness set
a.
Test harness
b.
LED harness
c.
LED
harness
adaptor
d.
Probe
General service tools Continuity check and voltage
measurement at harness wire or
connector for loose, corroded or
damaged terminals, or terminals
pushed back in the connector.
a.
Connector
pin
contact
pressure inspection
b.
Power circuit inspection
c.
Power circuit inspection
d.
Commercial tester connection
MB992006
MB992006
Extra fine probe
-
Continuity check and voltage
measurement at harness wire or
connector for loose, corroded or
damaged terminals, or terminals
pushed back in the connector.
DIAGNOSIS
STANDARD FLOW OF DIAGNOSTIC TROUBLESHOOTING
M15410800006USA0000010000
Refer to GROUP 00 - Troubleshooting contents P.
00-6.
TROUBLESHOOTING FOR NOISE
M15410800323USA0000010000
AM/FM RADIO AND CD PLAYER
The noise is generated during the engine run.
Check that no noise of external origin is present.
Because the signal reception becomes poor
indoors, check in the open air. If this check is
neglected, the source of noise cannot be
determined, resulting in a false recognition.
Therefore, be sure to perform this check.
When implementing the noise prevention, start
the prevention from the object causing the
strongest noise.
Check that the audio main body and others are
securely grounded.
AUDIO AND NAVIGATION SYSTEM
54B-5
DIAGNOSIS
Noise types
( ) indicates the
sound type.
Situation
Cause
Countermeasure
AM, FM:
(Crack,
tapping,
rattle, plash)
⦆
When the engine speed
is increased, the scratch
noise becomes faster
and the sound volume
decreases.
⦆
When the ignition switch
is turned to ACC, the
noise disappears.
⦆
Radiation noise caused
mainly by the spark plug
⦆
Noise wraparound
Check or replace the ground
cable ground bolt. (Refer to
Figure 1).
AM, FM:
Wiper motor noise
(hum,
distorted
hum)
Synchronized with the
wiper movement, and also
becomes faster when
wiper movement is sped
up. When the wiper is
stopped, the noise also
stops.
Caused by the sparks
generated by the wiper
motor brush.
Replace the wiper motor.
Noise from other
electrical
equipment
-
The noise may be generated
when
the
electrical
equipment become old.
Repair or replace the
electrical equipment.
Static
electricity
(cracking, popping)
No noise is generated
when the vehicle comes to
a complete stop.
The parts or wiring move for
some reason, and cause the
noise by contacting against
the body metal parts.
Return the parts and wiring
to the normal positions.
Various types of noise are
generated in various parts
of the body.
Caused by the looseness
between the body and the
hood,
liftgate,
bumper,
exhaust pipe and muffler,
suspension, or others.
Securely
tighten
the
mounting bolts of each part.
NOTE:
For trouble symptoms other than the noise,
perform the following troubleshooting procedures.
Refer to P.54B-18.
ZC3054050000
<Figure 1>
Power
steering
oil pump
DIAGNOSIS FUNCTION
M15410800321USA0000010000
DTC READING METHOD
Refer to GROUP 00, How to use Troubleshooting/inspection
Service Points, How to Cope with Intermittent Malfunction P.
00-15.
54B-6
AUDIO AND NAVIGATION SYSTEM
DIAGNOSIS
HOW TO ERASE DTC
Refer to GROUP 00, How to use Troubleshooting/inspection
Service Points, How to Cope with Intermittent Malfunction P.
00-15.
DATA LIST REFERENCE TABLE
M15410800080USA0000010001
Item No.
Check item (scan tool display)
Check condition
Normal condition
01
RADIO remote SW (SEEK-)
SEEK (-) switch: ON
ON
02
RADIO remote SW (SEEK+)
SEEK (+) switch: ON
ON
03
RADIO remote SW (MODE)
MODE switch: ON
ON
04
RADIO remote SW (VOL-)
VOL (-) switch: ON
ON
05
RADIO remote SW (VOL+)
VOL (+) switch: ON
ON
DIAGNOSTIC TROUBLE CODE CHART
M15410800079USA0000010000
On troubleshooting, if the ignition switch is turned
ON while disconnecting connector(s), diagnostic
trouble code(s) associated with other system may
be set. On completion, confirm all systems for
diagnostic trouble code(s). If diagnostic trouble
code(s) are set, erase them all.
DTC No.
Description
Reference page
U0019
Bus off (CAN-B)
U1415
Coding not completed or failed
B2420
Power supply circuit malfunction
B2421
Radio tuner failure
B2423
6-disc CD player error
B2450
Switch panel communication error
B2451
Panel type error
DIAGNOSTIC TROUBLE CODE PROCEDURES
DTC U0019: Bus off (CAN-B)
M15410800348USA0000010000
If there is any problem in the CAN bus lines, an
incorrect diagnostic trouble code may be set.
Prior to this diagnosis, always diagnose the CAN
bus lines.
Before replacing the radio and CD player or CD
changer, be sure to check that the power supply
circuit, ground circuit, and communication circuit
are normal.
TROUBLE JUDGMENT
When the radio and CD player or CD changer is
returned from the bus off state, or when the bus error
is indicated to the radio and CD player or CD changer
state, the DTC U0019 (CAN-B) is set.
AUDIO AND NAVIGATION SYSTEM
54B-7
DIAGNOSIS
COMMENTS ON TROUBLE SYMPTOM
The radio and CD player or CD changer, power supply
for the radio and CD player or CD changer, ground
circuit, or CAN bus line may have a problem.
PROBABLE CAUSES
⦆
Malfunctions of radio and CD player or CD changer
⦆
Malfunction of CAN bus line wiring harness and
connector
DIAGNOSIS
Required Special Tools:
⦆
MB991223: Harness Set
⦆
MB992006: Extra Fine Probe
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicle Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A
STEP 1. Using scan tool MB991958, diagnose the CAN bus
line.
Use scan tool MB991958 to diagnose the CAN bus lines.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
(1)
Connect scan tool MB991958 to the data link connector.
(2)
Turn the ignition switch to "ON" position.
(3)
Diagnose the CAN bus line.
Q:Is the check result normal?
YES:
Go to Step 2.
NO:
Repair the CAN bus line. (Refer to GROUP 54D,
Diagnosis P.54D-10.) On completion, go to Step 2.
STEP 2. Recheck for diagnostic trouble code.
Check again if the DTC is set to the radio and CD player or CD
changer.
(1)
Erase the DTC.
(2)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(3)
Check if the DTC is set.
Q:Is the DTC set?
YES:
Replace the radio and CD player or CD changer.
NO:
The trouble can be an intermittent malfunction (Refer
to GROUP 00, How to use Troubleshooting/inspection
Service Points, How to Cope with Intermittent
Malfunction P.00-15).
54B-8
AUDIO AND NAVIGATION SYSTEM
DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст