Mitsubishi Outlander XL. Manual — part 762
SPECIAL TOOLS
M14206000006USA0000010001
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
MB991910
MB991826
MB991911
MB991914
MB991824
MB991827
MB991825
Do not use
A
B
C
D
E
F
G
Do not use
YB9919580001
MB991958
A: MB991824
B: MB991827
C: MB991910
D: MB991911
E: MB991914
F: MB991825
G: MB991826
Scan tool (M.U.T.-III sub
assembly)
A:
Vehicle
communication
interface (V.C.I.)
B: M.U.T.-III USB
cable
C: M.U.T.-III main
harness A (Vehicles
with
CAN
communication
system)
D: M.U.T.-III main
harness B (Vehicles
without
CAN
communication
system)
E: M.U.T.-III main
harness C (for Daimler
Chrysler models only)
F:
M.U.T.-III
measurement adapter
G: M.U.T.-III trigger
harness
MB991824-KIT
NOTE:
G: MB991826
M.U.T.-III Trigger
Harness is not
necessary when pushing
V.C.I. ENTER key.
Communication line check
(ECU check and service data)
For vehicles with CAN
communication, use M.U.T.-
III main harness A to send
simulated vehicle speed. If
you connect M.U.T.-III main
harness B instead, the CAN
communication does not
function correctly.
SUNROOF
42Ad-35
SPECIAL TOOLS
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
YB9912230001
A
D
C
B
Do not use
MB991223 Harness set
A: MB991219 Test
harness
B: MB991220 LED
harness
C: MB991221 LED
harness adapter
D: MB991222 Probe
General service tools
Making voltage and resistance
measurement
during
troubleshooting
A: Connector pin contact
pressure inspection
B: Power circuit inspection
C: Power circuit inspection
D:
Commercial
tester
connection
MB992006
MB992006
Extra fine probe
-
Making voltage and resistance
measurement
during
troubleshooting
ON-VEHICLE SERVICE
WATER TEST
M14206000009USA0000010000
Check if there are any leaks in the sunroof by the following
procedure.
1.
Fully close the sunroof lid glass.
2.
Adjust the water pressure so that water comes out of the hose
to a height of approximately 50 cm (19.7 inches) when the
hose is held vertically facing upwards.
ZC6001210000
Hose
Approximately
30 cm (11.8 in)
3.
Hold the end of the hose approximately 30 cm (11.8 inches)
above the roof and let the water run onto the weatherstrip for
5 minutes or more.
4.
Check if any water leaks can be found in the room while
watering. Even though there are any water leaks around the
sunroof lid glass, it can be acceptable as long as water is
caught in the drip area.
SUNROOF FIT ADJUSTMENT
M14206000010USA0000010000
1.
Fully close the sunroof lid glass.
2.
Fully open the sunshade.
42Ad-36
SUNROOF
ON-VEHICLE SERVICE
ZC6002980000
3.
Loosen the sunroof lid glass assembly mounting screws.
Adjust the sunroof lid glass height by moving the sunroof lid
glass assembly along the sunroof lid guide oblong hole so that
the clearance between the sunroof lid glass and the vehicle
body is even throughout the circumference.
4.
After adjustment, check that the sunroof operates smoothly.
SUNROOF SAFETY FUNCTION CHECK
M14206000044USA0000010000
1.
Close the sunroof lid glass while placing an approximately 10
mm thick piece of wood at right angles with the sunroof lid
glass.
2.
Check to see if the sunroof motor assembly turns in the
opposite direction and the sunroof lid glass opens when the
sunroof lid glass touches the wood. If any problem occurs,
perform troubleshooting. (Refer to P.42Ad-4.)
SUNROOF CHECK
M14206000047USA0000010001
Check to see that the sunroof operates by pressing the sunroof
switch. If it does not operate, perform troubleshooting. Refer
to P.42Ad-4.
SUNROOF TIMER FUNCTION CHECK
M14206000043USA0000010000
Check the system as described below. If the system does not
work, carry out troubleshooting. Refer to P.42Ad-4.
⦆
Close the door and turn the ignition switch to the LOCK (OFF)
position, and then check that the sunroof operates for 30
seconds.
⦆
Close the door and turn the ignition switch to the LOCK (OFF)
position. While the timer is on, open the driver's door and front
passenger's door, and check that the sunroof stays during the
operation. (When the driver's door or front passenger's door
is opened while the timer is on, the timer will be turned off.)
SUNROOF
42Ad-37
ON-VEHICLE SERVICE
SUNROOF LID GLASS OPERATION CURRENT
CHECK
M14206000032USA0000010000
ZC6011500003
Sunroof fuse
ETACS-ECU
1.
Remove the fuse of the sunroof, then connect the circuit tester
as shown in the Figure.
2.
Turn ON the sunroof switch, then measure the operating
current when the sunroof lid glass is halfway opened.
Standard value: 7 A or less [at 20 °C (68 °F)]
3.
Check the following areas if the operating current exceeds the
standard value:
⦆
Sunroof installation, deformation and presence of any
foreign substances.
⦆
Drive cable installation.
⦆
Tilting of sunroof lid glass.
LEARNING PROCEDURES OF THE SUNROOF
FULLY CLOSED POSITION
M14206000046USA0000010000
SHIFTING CONDITIONS FOR THE FULLY CLOSED
POSITION ADJUSTMENT MODE
⦆
When shifting to the forced fully closed position adjustment
mode
How to shift to the forced fully closed position adjustment
mode
1.
Turn the ignition switch to the "ON" position.
2.
With the sunroof lid glass stopped (the position of the
sunroof lid glass can be any position between fully
opened and fully closed), press and hold the up switch
for 10 seconds.
⦆
When the anti-trap function (safety mechanism) is activated
consecutively five times
⦆
When the position information may be incorrect due to
abnormal power supply during the sunroof operation
NOTE:
When installing the sunroof assembly, or installing/
replacing the sunroof motor assembly, operate the forced
fully closed position adjustment mode to adjust the fully
closed position.
HOW TO ADJUST THE FULLY CLOSED POSITION
FORCED FULLY CLOSED POSITION
ADJUSTMENT MODE
1.
With the sunroof lid glass stopped (the position of the sunroof
lid glass can be any position between fully opened and fully
closed), press and hold the up switch.
NOTE:
If operating the up switch moves the sunroof
normally, use the open switch to fully open the sunroof
42Ad-38
SUNROOF
ON-VEHICLE SERVICE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст