Mitsubishi Outlander XL. Manual — part 188

Required Special Tools:

｠

MB992075: Handle

｠

MB992183: Crankshaft Rear Oil Seal Installer

｠

MD998781: Flywheel Stopper

REMOVAL SERVICE POINT

<<A>> DRIVE PLATE BOLT REMOVAL

ZK602109AA00

MD998781

1.

Using special tool MD998781, hold the drive plate.

2.

Remove the drive plate bolt.

INSTALLATION SERVICE POINTS

>>A<< CRANKSHAFT SENSING RING INSTALLATION

1.

Apply the engine oil to the thread portions and the sealed
portions on the installation bolts.

ZK6006540000

1

2

3

2.

In accordance with the tightening order shown in the
illustration, tighten the crankshaft sensing ring to the specified
torque.

Tightening torque: 12 ± 2 N·m (106 ± 17 in-lb)

>>B<< CRANKSHAFT BEARING UPPER INSTALLATION

ZK600656

No.4

Cylinder
bore size

No.3 No.2

No.1

0000

Right side

Timing belt side

Crankshaft journal (Upper)

identification mark

1.

If the upper crankshaft bearing is replaced, select based on
the identification mark of cylinder block (illustrated) and the
table shown below.

Crankshaft journal (Upper) Crankshaft bearing
Identification mark

Identification mark

Number 1 and 4 journal
1

1

2

2

3

3

Number 2 and 3 journal

ENGINE OVERHAUL

11B-71

CRANKSHAFT AND CYLINDER BLOCK

Crankshaft journal (Upper) Crankshaft bearing
Identification mark

Identification mark

0

0

1

1

2

2

ZK6006570000

Identification
mark

2.

The upper crankshaft bearing has the identification mark on
the location shown in the illustration.

3.

Install the upper selected crankshaft bearing.

>>C<< CRANKSHAFT THRUST BEARING INSTALLATION

ZK500353AA00

Groove

1.

Install the thrust bearing in the No.3 bearing bore in the
cylinder block and in the bearing cap. For easier installation,
apply engine oil to the bearings; this will help hold them in
position.

2.

The thrust bearings must be installed with their groove toward
the crankshaft web.

>>D<< CRANKSHAFT BEARING LOWER INSTALLATION

ZK600655

Crankshaft
No.5 jornal

No.1

Model name

2D code

No.2

No.3

No.4

Spare

0000

Crankshaft pin

identification mark

Crankshaft journal (Lower)

identification mark

1.

If the lower crankshaft bearing is replaced, select based on the
identification mark of crankshaft (illustrated) and the table
shown below.

Crankshaft journal (Lower) Crankshaft bearing
Identification mark

Identification mark

0

0

1

1

2

2

3

3

4

4

11B-72

ENGINE OVERHAUL

CRANKSHAFT AND CYLINDER BLOCK

ZK6006580000

Identification
mark

2.

The lower crankshaft bearing has the identification mark on
the location shown in the illustration.

3.

Install the lower selected crankshaft bearing.

>>E<< BEARING CAP / BEARING CAP BOLT
INSTALLATION

ZK604073 0000

Shank length

1.

Before installing the bearing cap bolt, check the bolt screw
head is not damaged. If the screw head extremely gets
damaged, replace it with a new bolt. The standard length of
the new bolt measured from under the head is as follows:

Standard value: 91.2 - 92.2 mm (3.59 - 3.63 inches)

ZK601900

5

8

7

4

2

3

1

6

5

8

7

2

3

4

1

6

0000

Front mark

Crankshaft

Cylinder block

2.

Attach the bearing cap on the cylinder block as shown in the
illustration.

3.

Tighten the bearing cap bolts to specified torque in the
sequence shown in the illustration.

ENGINE OVERHAUL

11B-73

CRANKSHAFT AND CYLINDER BLOCK

Tightening torque: 24 ± 2 N·m (18 ± 1 ft-lb)

ZK601901AA00

Paint mark

Paint mark

90˚

4.

Make a paint mark on the head of each bolt.

｠

If the bolt is overtightened, loosen the bolt completely and
then retighten it by repeating the tightening procedure
from step 2.

｠

If the bolt is turned less than 90 degrees, proper fastening
performance may not be achieved. Be sure to turn the bolt
exactly 90 degrees.

5.

Make a paint mark on the bearing cap 90 degrees from the
paint mark made on the bolt, in the direction of tightening the
bolt.

6.

Turn each bolt 90 degrees in the tightening sequence
specified in step 2, and make sure that the paint marks on the
bolt and cap are aligned.

7.

Check that the crankshaft rotates smoothly.

ZK602460AA00

8.

Check the end play. If it exceeds the limit value, replace the
thrust bearing.

Standard value: 0.05 - 0.25 mm (0.002 - 0.009 inch)
Limit: 0.3 mm (0.01 inch)

11B-74

ENGINE OVERHAUL

CRANKSHAFT AND CYLINDER BLOCK