Mitsubishi Outlander XL. Manual — part 1010
STEP 6. Retest the system.
Check that the taillight illuminates normally.
Q:Does the taillight work normally?
YES:
The trouble can be an intermittent malfunction
(Refer to GROUP 00 - How to use Troubleshooting/
inspection Service Points - How to Cope with Intermittent
Malfunction P.00-15).
NO:
Replace the rear combination light unit.
DIAGNOSIS
STANDARD FLOW OF DIAGNOSTIC TROUBLESHOOTING
M15410900005USA0000010003
Refer to GROUP 00 - Contents of troubleshooting P.
00-6.
DIAGNOSTIC FUNCTION
M15410900006USA0000010004
HOW TO CONNECT THE SCAN TOOL (M.U.T.-III)
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicle Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
1.
Ensure that the ignition switch is at the "LOCK" (OFF) position.
2.
Start up the personal computer.
3.
Connect special tool MB991827 to special tool MB991824 and
the personal computer.
4.
Connect special tool MB991910 to special tool MB991824.
5.
Connect special tool MB991910 to the data link connector.
6.
Turn the power switch of special tool MB991824 to the "ON"
position.
NOTE:
When special tool MB991824 is energized, special
tool MB991824 indicator light will be illuminated in a
green color.
7.
Start the M.U.T.-III system on the personal computer.
NOTE:
Disconnecting scan tool MB991958 is the reverse of
the connecting sequence, making sure that the ignition
switch is at the "LOCK" (OFF) position.
LIGHTING
54Ac-113
DIAGNOSIS
HOW TO READ AND ERASE DIAGNOSTIC
TROUBLE CODES
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicle Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
NOTE:
If the battery voltage is low, diagnostic trouble
codes will not be set. Check the battery if scan tool
MB991958 does not display.
1.
Connect scan tool MB991958 to the data link connector.
2.
Turn the ignition switch to the "ON" position.
3.
Select "System select" from the start-up screen.
4.
Select "From 2006 MY" of "Model Year." When the "Vehicle
Information" is displayed, check the contents.
5.
Select "ETACS" from "System List", and press the "OK"
button.
NOTE:
When the "Loading Option Setup" list is displayed,
check the applicable item.
6.
Select "Diagnostic Trouble Code."
7.
If a DTC is set, it is shown.
8.
Choose "Erase DTCs" to erase the DTC.
TROUBLE SYMPTOM CHART
M15410900009USA0000010003
Trouble symptom
Inspection
Procedure No.
Reference
page
Fog lights do not illuminate normally.
1
The right or left fog light does not illuminate.
2
Fog light indicator does not illuminate/go out normally.
3
SYMPTOM PROCEDURES
Inspection Procedure 1: Fog lights do not illuminate normally.
M15410900168USA0000010000
Whenever the ECU is replaced, ensure that the input and
output signal circuits are normal.
54Ac-114
LIGHTING
DIAGNOSIS
FUSIBLE
LINK
36
FOG LIGHT
RELAY
FRONT
FOG
LIGHT
RELAY BOX
ENGINE
COMPARTMENT
ETACS-ECU
Fog Light and ETACS-ECU Communication Circuit
ZC600878003
Connector: C-312
C-312
ZC6041270002
Connector: A-14X
LIGHTING
54Ac-115
DIAGNOSIS
ZC6008720009
Connector: A-41, A-46
A-41 (B)
A-41 (B)
A-46 (B)
ZC6008710012
Connector: A-51
A-51 (B)
CIRCUIT OPERATION
If the fog lights do not illuminate normally, the input signal circuit
(s) below or the ETACS-ECU may be defective.
⦆
Tail light switch
⦆
Headlight switch
⦆
Fog light switch
⦆
Option coding information
TECHNICAL DESCRIPTION (COMMENT)
When the fog lights do not illuminate normally, the mentioned
input signal circuit(s) or ETACS-ECU may be defective.
TROUBLESHOOTING HINTS
⦆
Malfunction of the column switch
⦆
Malfunction of the ETACS-ECU
⦆
Damaged harness wires and connectors
DIAGNOSIS
Required Special Tools:
⦆
MB991223: Harness Set
⦆
MB992006: Extra Fine Probe
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: V.C.I.
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A
54Ac-116
LIGHTING
DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст