Mitsubishi Outlander XL. Manual — part 461

STEP 2. Check the symptoms.

Q:"CANCEL" switch is pressed, auto-cruise control system

is cancelled?

YES:

It can be assumed that this malfunction is

intermittent (Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points - How to Cope
with Intermittent Malfunctions P.00-15).

NO:

Replace the ECM. When the ECM is replaced, register

the encrypted code (Refer to GROUP 42C, Diagnosis - ID
Code Registration Necessity Judgment Table P.42C-8).
Then go to Step 3.

STEP 3. Check the symptoms.

Q:"CANCEL" switch is pressed, auto-cruise control system

is cancelled?

YES:

The procedure is complete.

NO:

Return to Step 1.

Inspection Procedure 4: Auto-cruise Control System cannot be Set.

M11702000042USA0000010000

COMMENT
The fail-safe function is probably canceling auto-
cruise control system. In this case, checking the auto-
cruise control system, MFI system, A/T system and
CAN bus line system for diagnostic trouble codes. The
scan tool MB991958 can also be used to check if the
circuits of each input switch are normal or not by
checking the input switch codes.

TROUBLESHOOTING HINTS (The most likely
causes for this case:)

｠

Malfunction of the CAN bus line system.

｠

Malfunction of the MFI system.

｠

Malfunction of the A/T system.

｠

Malfunction of the auto-cruise control switch.

｠

Malfunction of the stoplight switch.

｠

Malfunction of the transmission range switch.

｠

Malfunction of the ECM.

DIAGNOSIS

Required Special Tools:

｠

MB991958: Scan Tool (M.U.T.-III Sub Assembly)

｠

MB991824: V.C.I.

｠

MB991827: M.U.T.-III USB Cable

｠

MB991910: M.U.T.-III Main Harness A

AUTO-CRUISE CONTROL SYSTEM

17b-37

AUTO-CRUISE CONTROL SYSTEM DIAGNOSIS

STEP 1. Using scan tool MB991958, diagnose the CAN bus
line.

ZC501967

AC404789

ZC5019680000

MB991824

MB991827

MB991910

Data link

connector

To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.

(1)

Connect scan tool MB991958 to the data link connector
(Refer to P.17b-5).

(2)

Turn the ignition switch to the "ON" position.

(3)

Diagnose the CAN bus line (Refer to P.17b-5).

(4)

Turn the ignition switch to the "LOCK" (OFF) position.

(5)

Disconnect scan tool MB991958.

Q:Is the check result satisfactory?

YES:

Go to Step 2

NO:

Repair the CAN bus lines (Refer to GROUP 54D,

Diagnosis - CAN Bus Diagnostics Chart P.54D-17). Then
go to Step 9.

STEP 2. Using scan tool MB991958, read the MFI system
diagnostic trouble code.

(1)

Connect scan tool MB991958 to the data link connector
(Refer to P.17b-5).

(2)

Turn the ignition switch to the "ON" position.

(3)

Check for MFI system diagnostic trouble code (Refer to
GROUP 13Ab, Diagnostic Function - How to Read and Erase
Diagnostic Trouble Codes P.13Ab-8).

(4)

Turn the ignition switch to the "LOCK" (OFF) position.

(5)

Disconnect scan tool MB991958.

Q:Is any DTC set?

YES:

Diagnose the MFI system (Refer to GROUP 13Ab,

Diagnostic Trouble Code Chart P.13Ab-44). Then go to Step
9.

NO:

Go to Step 3.

STEP 3. Using scan tool MB991958, read the A/T system
diagnostic trouble code.

(1)

Connect scan tool MB991958 to the data link connector
(Refer to P.17b-5).

(2)

Turn the ignition switch to the "ON" position.

(3)

Check for A/T system diagnostic trouble code (Refer to
GROUP 23A, Automatic Transaxle Diagnosis - Diagnostic
Function - How to Read and Erase Diagnostic Trouble
Code P.23A-15).

(4)

Turn the ignition switch to the "LOCK" (OFF) position.

(5)

Disconnect scan tool MB991958.

Q:Is any DTC set?

17b-38

AUTO-CRUISE CONTROL SYSTEM

AUTO-CRUISE CONTROL SYSTEM DIAGNOSIS

YES:

Diagnose the A/T system (Refer to GROUP 23A,

Automatic Transaxle Diagnosis - Diagnostic Trouble Code
Chart P.23A-22). Then go to Step 9.

NO:

Go to Step 4.

STEP 4. Read the diagnostic trouble code.
Read the auto-cruise control system diagnostic trouble code
(Refer to P.17b-5).

Q:Is DTC set?

YES:

Diagnose the auto-cruise control system (Refer

to P.17b-7, Diagnostic Trouble Code Chart). Then go to
Step 9.

NO:

Go to Step 5.

STEP 5. Using scan tool MB991958, check the data list item
86: Main switch, item 92: Set switch, item 91: Resume
switch and item 75: Cancel switch.

To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.

(1)

Connect scan tool MB991958 to the data link connector
(Refer to P.17b-5).

(2)

Turn the ignition switch to the "ON" position.

(3)

Set scan tool MB991958 to data reading mode for auto-cruise
control system (Refer to P.17b-5).

｠

Item 86: Main switch.

｠

When "ON/OFF" switch is at the "ON" position, the
display on scan tool MB991958 should be "ON".

｠

When "ON/OFF" switch is at the "OFF" position, the
display on scan tool MB991958 should be "OFF".

｠

Item 92: Set switch.

｠

When "COAST/SET" switch is at the "ON" position, the
display on scan tool MB991958 should be "ON".

｠

When "COAST/SET" switch is at the "OFF" position,
the display on scan tool MB991958 should be "OFF".

｠

Item 91: Resume switch.

｠

When "ACC/RES" switch is at the "ON" position, the
display on scan tool MB991958 should be "ON".

｠

When "ACC/RES" switch is at the "OFF" position, the
display on scan tool MB991958 should be "OFF".

｠

Item 75: Cancel switch.

｠

When "CANCEL" switch is at the "ON" position, the
display on scan tool MB991958 should be "ON".

｠

When "CANCEL" switch is at the "OFF" position, the
display on scan tool MB991958 should be "OFF".

(4)

Turn the ignition switch to the "LOCK" (OFF) position.

(5)

Disconnect scan tool MB991958.

Q:Is the switch operating properly?

YES:

Go to Step 6.

AUTO-CRUISE CONTROL SYSTEM

17b-39

AUTO-CRUISE CONTROL SYSTEM DIAGNOSIS

NO:

Refer to P.17b-8, Diagnostic Trouble Code Procedures

- DTC 15: Auto-cruise Control Switch System. Then go to
Step 9.

STEP 6. Using scan tool MB991958, check the data list item
74: Brake light switch, item 290: Brake light switch.

(1)

Connect scan tool MB991958 to the data link connector
(Refer to P.17b-5).

(2)

Turn the ignition switch to the "ON" position.

(3)

Set scan tool MB991958 to data reading mode for auto-cruise
control system (Refer to P.17b-5).

｠

Item 74, Brake light switch.

｠

When the brake pedal is depressed, the display on
scan tool MB991958 should be "ON".

｠

When the brake pedal is released, the display on scan
tool MB991958 should be "OFF".

｠

Item 290, Brake light switch.

｠

When the brake pedal is depressed, the display on
scan tool MB991958 should be "ON".

｠

When the brake pedal is released, the display on scan
tool MB991958 should be "OFF".

(4)

Turn the ignition switch to the "LOCK" (OFF) position.

(5)

Disconnect scan tool MB991958.

Q:Is the switch operating properly?

YES:

Go to Step 7.

NO:

Refer to P.17b-17, Diagnostic Trouble Code

Procedures - DTC 22: Stoplight Switch System. Then go to
Step 9.

STEP 7. Using scan tool MB991958, check data list item 88:
Neutral switch.

(1)

Connect scan tool MB991958 to the data link connector
(Refer to P.17b-5).

(2)

Turn the ignition switch to the "ON" position.

(3)

Set scan tool MB991958 to data reading mode for auto-cruise
control system (Refer to P.17b-5).

｠

Item 88, Neutral switch.

｠

When selector lever is at the "N" position, the display
on scan tool MB991958 should be "ON".

｠

When selector lever is other than "N" position, the
display on scan tool MB991958 should be "OFF".

(4)

Turn the ignition switch to the "LOCK" (OFF) position.

(5)

Disconnect scan tool MB991958.

Q:Is the switch operating properly?

YES:

Go to Step 8.

NO:

Refer to P.17b-17, Symptom Procedures - Inspection

Procedure 2. Then go to Step 9.

STEP 8. Check the symptoms.

Q:Can auto-cruise control be set?

YES:

It can be assumed that this malfunction is

intermittent (Refer to GROUP 00, How to Use

17b-40

AUTO-CRUISE CONTROL SYSTEM

AUTO-CRUISE CONTROL SYSTEM DIAGNOSIS