Mitsubishi Outlander XL. Manual — part 978

Display contents

System operation state

Action procedure

ZC602332

ZC602333

ZC602334

ZC6023350000

Displays the screen in accordance
with operation state of the AWD
selector switch.

If the AWD selector switch position and
screen do not agree with each other, perform
the troubleshooting for the AWD. Refer to
GROUP 27C, Diagnosis P.27C-74.

ZC6023360000

Displayed when the ASC is in
operation.

If the warning screen is not displayed
normally or if the screen continues to be
displayed, perform the troubleshooting for the
ASC. Refer to GROUP 35C, Symptom
Chart P.35C-160.

ZC6023370000

Displayed when the corner sensor
detects obstacles.

If the screen is not displayed even when the
obstacle is in a distance that the detection
should be made, or if there is an abnormal
display, perform the troubleshooting for the
corner sensor system. Refer to P.54Ab-40.

PERIODIC
INSPECTION

ZC6023380000

Displayed when the set period
elapses.

-

REST REMINDER

ZC6023390000

Displayed when the set time
elapses.

-

ON-VEHICLE SERVICE

SPEEDOMETER CHECK

M15410100038USA0000010000

1.

Adjust the pressure of tires to the specified level (Refer to
GROUP 31, On-vehicle Service P.31-7).

2.

Where applicable, ensure that the TPMS warning light is not
illuminating or flashing.

COMBINATION METER

54Ab-65

ON-VEHICLE SERVICE

Do not accelerate or decelerate suddenly during servicing
work.

ZC6033440000

<FWD>

WHEEL CHOCKS

Set a free-roller on the rear tire for AWD.

3.

For FWD vehicles, set the vehicle onto a speedometer tester
and use wheel chocks to hold the rear wheels.

ZC6033450000

FREE ROLLER

<AWD>

4.

For AWD vehicles, set the vehicle onto a speedometer tester
and place the rear wheels on a free roller.

ZC5012710000

FRONT

ANCHOR PLATE

PULLER

5.

To prevent the front wheel from moving from side to side,
attach tension bars to the tie-down hook, and secure both
ends to anchor plates.

6.

To prevent the vehicle from moving, attach a chain or wire to
the rear retraction hook, and make sure the end of the chain
or wire is secured.

7.

Check if the speedometer indicator range is within the
standard values.

Standard value <Except vehicles for CANADA>:

Standard indication mph
(km/h)

Allowance range mph (km/
h)

10 (16)

8.5 - 11.5 (13.6 - 18.4)

25 (40)

23.5 - 26.5 (37.6 - 42.4)

50 (80)

48.5 - 51.5 (77.6 - 82.4)

75 (120)

73.5 - 76.5 (117.6 - 122.4)

100 (161)

98.5 - 102.5 (158.6 - 165.0)

125 (201)

123.5 - 127.5 (198.6 - 205.0)

Standard value <Vehicles for CANADA>:

standard indication km/h
(mph)

Allowance range km/h
(mph)

20 (12.4)

19 - 24 (11.8 - 14.9)

40 (24.8)

40 - 44 (24.8 - 27.3)

80 (49.7)

80 - 85 (49.7 - 52.8)

120 (74.6)

120.5 - 125.5 (74.9 - 78.0)

54Ab-66

COMBINATION METER

ON-VEHICLE SERVICE

standard indication km/h
(mph)

Allowance range km/h
(mph)

160 (99.4)

160.5 - 165.5 (99.7 - 102.8)

200 (124.3)

200.5 - 207.0 (124.6 - 128.6)

8.

If not within the standard value, check the tire size. If an
incorrect size of tire is used, replace it and check again. If the
tire size is correct, a defect may be present in components and
circuit between the output shaft speed sensor and the
combination meter. Check the following items.

｠

output shaft speed sensor (refer to GROUP23A, Automatic
Transaxle Diagnosis P.23A-22).

｠

Combination meter (refer to P.54Ab-7).

TACHOMETER CHECK

M15410100039USA0000010000

When the actuator tests (item No.2) are performed
using scan tool MB991958, check that the tachometer
indication error is within the standard value.

NOTE:

Values in ( ) indicates the reference

value.

Standard value:

Engine speed r/min

Tachometer

indicating

error r/min

600

550 - 650

(2,000)

(1,950 - 2,050)

Engine speed r/min

Tachometer

indicating

error r/min

3,000

2,950 - 3,050

(4,000)

(3,950 - 4,050)

5,000

4,950 - 5,050

6,000

5,950 - 6,050

(7,000)

(6,950 - 7,050)

(8,000)

(7,950 - 8,050)

FUEL LEVEL SENSOR CHECK

M15410100040USA0000010000

VEHICLES FOR FWD

1.

Remove the second seat (Refer to GROUP 52A - Seat
Assembly P.52A-21).

2.

Remove the floor inspection lid, and then remove the fuel
pump module (Refer to GROUP 13B - Fuel Tank P.13B-13).

COMBINATION METER

54Ab-67

ON-VEHICLE SERVICE

NOMINAL RESISTANCE OF THE FUEL LEVEL SENSOR

ZC608190000

Ground

Fuel level sensor

Stopper position “F”

Stopper position “E”

When float of the fuel level sensor is in stopper positions F and
E, ensure that resistance between the fuel level sensor terminal
and earth terminal is within the standard value.

Standard value:

Float position

Gauge resistance value (ohms)

Stopper position "F" 13.0 ± 1.0
Stopper position "E" 120.0 ± 1.0

When the float is moved slowly between stopper positions "F"
and "E", ensure that the resistance is smoothly changing.

FUEL LEVEL SENSOR FLOAT HEIGHT

ZC6038200000

B

A

Stopper position “E”

Stopper position “F”

When float is moved to contact the float arm on the stopper,
ensure that stopper positions "F" (height A) and "E" (height B)
are within the standard value.

Standard value:

Float position

Float height mm (in)

Stopper position "F" (height A) 201.9 (7.9)
Stopper position "E" (height B) 18.3 (0.7)

VEHICLES FOR AWD

1.

Remove the second seat (Refer to GROUP 52A - Seat
Assembly P.52A-21).

2.

Remove the floor inspection lid, and then remove the fuel
pump module and fuel level sensor (sub) (Refer to GROUP
13B - Fuel Tank P.13B-18).

54Ab-68

COMBINATION METER

ON-VEHICLE SERVICE