Mitsubishi Outlander XL. Manual — part 1034
STEP 5. Recheck for diagnostic trouble code.
Check again if the DTC is set to the ETACS-ECU.
(1)
Erase the DTC.
(2)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(3)
Check if DTC is set.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the DTC set?
YES:
Replace the ETACS-ECU.
NO:
The trouble can be an intermittent malfunction such
as a poor connection or open circuit in the CAN bus lines
between the transaxle control module and the ETACS-ECU.
(Refer to GROUP 00, How to Cope with Intermittent
Malfunction P.00-15)
DTC U0114: AWD-ECU CAN timeout
M15410600053USA0000010000
⦆
If DTC U0114 is set to the ETACS-ECU, always
diagnose the CAN bus line.
⦆
Before replacing the ECU, ensure that the
communication circuit is normal.
TROUBLE JUDGMENT
If the signal from AWD-ECU cannot be received, the
ETACS-ECU sets DTC U0114.
JUDGMENT CRITERIA
After the following statuses continue to be true for 5
seconds, if the communication with the AWD-ECU
cannot be established for 0.6 second or more, the
ETACS-ECU determines that a problem has
occurred.
⦆
No abnormality is present to the network.
⦆
Ignition switch is in the ON position.
⦆
No abnormality is present to the power supply fuse,
or the odometer value is at 80.5 km (50.0 miles) or
more.
⦆
ETACS-ECU system voltage is at 10-16 volts.
TROUBLESHOOTING HINTS
⦆
The AWD-ECU may be defective.
⦆
The ETACS-ECU may be defective.
⦆
The CAN bus may be defective.
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicle Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
ETACS
54Ad-15
DIAGNOSIS
STEP 1. Using scan tool MB991958, diagnose the CAN bus
line.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958. Refer to "How to connect the
Scan Tool (M.U.T.-III) P.54Ad-5."
(2)
Turn the ignition switch to the "ON" position.
(3)
Diagnose the CAN bus line.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the CAN bus line found to be normal?
YES:
Go to Step 2.
NO:
Repair the CAN bus line. (Refer to GROUP 54D,
STEP 2. Using scan tool MB991958, read the AWD-ECU
diagnostic trouble code
Check if DTC is set to the AWD-ECU.
Q:Is the DTC set?
YES:
Troubleshoot the electronic control AWD. (Refer to
GROUP 27C, Troubleshooting P.27C-9.)
NO:
Go to Step 3.
STEP 3. Using scan tool MB991958, read the combination
meter diagnostic trouble code.
Check if the DTC U0114 is set to the combination.
Q:Is the DTC set?
YES:
Go to Step 4.
NO:
Go to Step 5.
STEP 4. Recheck for diagnostic trouble code.
Check again if the DTC is set to the ETACS-ECU.
(1)
Erase the DTC.
(2)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(3)
Check if DTC is set.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the DTC set?
YES:
Replace the AWD-ECU.
NO:
The trouble can be an intermittent malfunction such
as a poor connection or open circuit in the CAN bus lines
between the AWD-ECU and the ETACS-ECU. (Refer to GROUP 00,
How to Cope with Intermittent Malfunction P.00-15)
54Ad-16
ETACS
DIAGNOSIS
STEP 5. Recheck for diagnostic trouble code.
Check again if the DTC is set to the ETACS-ECU.
(1)
Erase the DTC.
(2)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(3)
Check if DTC is set.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the DTC set?
YES:
Replace the ETACS-ECU.
NO:
The trouble can be an intermittent malfunction such
as a poor connection or open circuit in the CAN bus lines
between the AWD-ECU and the ETACS-ECU. (Refer to GROUP 00,
How to Cope with Intermittent Malfunction P.00-15)
DTC U0121: ABS-ECU or ASC-ECU CAN timeout
M15410600054USA0000010000
⦆
If DTC U0121 is set to the ETACS-ECU, always
diagnose the CAN bus line.
⦆
Before replacing the ECU, ensure that the
communication circuit is normal.
TROUBLE JUDGMENT
If the signal from ABS-ECU or ASC-ECU cannot be
received, the ETACS-ECU sets DTC U0121.
JUDGMENT CRITERIA
After the following statuses continue to be true for 5
seconds, if the communication with the ABS-ECU or
ASC-ECU cannot be established for 0.6 second or
more, the ETACS-ECU determines that a problem
has occurred.
⦆
No abnormality is present to the network.
⦆
Ignition switch is in the ON position.
⦆
No abnormality is present to the power supply fuse,
or the odometer value is at 80.5 km (50.0 miles) or
more.
⦆
ETACS-ECU system voltage is at 10-16 volts.
TROUBLESHOOTING HINTS
⦆
The ABS-ECU may be defective.
⦆
The ASC-ECU may be defective.
⦆
The ETACS-ECU may be defective.
⦆
The CAN bus may be defective.
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicle Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
ETACS
54Ad-17
DIAGNOSIS
STEP 1. Using scan tool MB991958, diagnose the CAN bus
line.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958. Refer to "How to connect the
Scan Tool (M.U.T.-III) P.54Ad-5."
(2)
Turn the ignition switch to the "ON" position.
(3)
Diagnose the CAN bus line.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the CAN bus line found to be normal?
YES:
Go to Step 2.
NO:
Repair the CAN bus line. (Refer to GROUP 54D,
STEP 2. Using scan tool MB991958, check for any ABS or
ASC diagnostic trouble code.
Check if DTC is set to the ABS-ECU or ASC-ECU.
Q:Is the DTC set?
YES:
Troubleshoot the ABS or ASC. (Refer to GROUP 35B,
Diagnosis P.35B-9<ABS> or GROUP 35C, Diagnosis P.
35C-11<ASC>.)
NO:
Go to Step 3.
STEP 3. Using scan tool MB991958, read the transaxle
control module diagnostic trouble code.
Check if the DTC U0121 is set to the transaxle control module
ECU.
Q:Is the DTC set?
YES:
Go to Step 4.
NO:
Go to Step 5.
STEP 4. Recheck for diagnostic trouble code.
Check again if the DTC is set to the ETACS-ECU.
(1)
Erase the DTC.
(2)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(3)
Check if DTC is set.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the DTC set?
YES:
Replace the ABS-ECU or ASC-ECU.
NO:
The trouble can be an intermittent malfunction such
as a poor connection or open circuit in the CAN bus lines
between the ABS-ECU or ASC-ECU and the ETACS-ECU. (Refer
54Ad-18
ETACS
DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст