Mitsubishi Outlander XL. Manual — part 708
ZC5018330000
5
1
9
9
6
7
11
7
2
3
4
1
11
8
10
N
Claw
Claw
Claw
Claw
<Vehicles without remote
controlled audio switch>
<Vehicles with remote
controlled audio switch>
2.5 ± 0.5 N·m
22.1 ± 4.4 in-lb
9.5 ± 2.5 N·m
84 ± 22 in-lb
9.5 ± 2.5 N·m
84 ± 22 in-lb
44 ± 11 N·m
33 ± 8 ft-lb
Removal steps
<<A>>
1.
Cover
>>B<<
2.
Horn connector connection
>>B<<
3.
Audio control switch connector
connection <Vehicles with audio
control switch>
<<B>>
>>B<<
4.
Air bag module connector connection
5.
Telematic cover
6.
Telematic switch
Removal steps
<<C>>
7.
Air bag module
8.
Cruise control switch
9.
Bezel switch or Remote controlled
radio switch
10. Self-locking nut
<<D>>
>>A<<
11. Steering wheel assembly
Required Special Tools:
⦆
MB990784: Ornament Remover
⦆
MB990803: Steering wheel puller
REMOVAL SERVICE POINTS
<<A>> COVER REMOVAL
ZC501834
Cover
0000
MB990784
Insert the special tool MB990784 at the indicated position to
remove the cover.
NOTE:
The special tool MB990784 can be inserted through the
notch behind the area shown.
POWER STEERING
37-21
STEERING WHEEL
<<B>> AIR BAG MODULE ASSEMBLY CONECTOR
DISCONNECTION
ZC601709
AC600868
Outer housing of the driver’s air bag
module connector
Horn connector
Lower column cover
0000
Driver’s air bag
module connector
(4-pin, yellow)
Slide the outer housing of the driver's air bag module connector
in the arrow direction shown, and disconnect the connector.
<<C>> AIR BAG MODULE REMOVAL
⦆
Never use an electric tester to diagnose the air bag
module circuit. Never attempt to disassemble the air bag
module.
⦆
Be sure to store the removed air bag module in a clean
and dry place with a pad surface facing upward.
<<D>> STEERING WHEEL ASSEMBLY REMOVAL
1.
Position the steering wheel in a straight ahead direction.
Use the special tool to remove the steering wheel since the
steering column collision absorbing mechanism may be
damaged.
37-22
POWER STEERING
STEERING WHEEL
ZC501836
MB990784
0000
2.
Use special tool MB990803 to remove the steering wheel
INSTALLATION SERVICE POINTS
>>A<< STEERING WHEEL ASSEMBLY INSTALLATION
After centering the clock spring (Refer to GROUP 52B - Air Bag
Module Clock Spring P.52B-329.), install the steering wheel
assembly.
>>B<< AIR BAG MODULE CONNECTOR CONNECTION/
AUDIO CONTROL SWITCH CONNECTOR CONNECTION/
HORN CONNECTOR CONNECTION
Connect the connector securely and route the harnesses not to
lie off the cover hole.
STEERING SHAFT
REMOVAL AND INSTALLATION
M13702000115USA0000010000
⦆
Before removing the steering wheel/air bag
module assembly, refer to GROUP 52B - Service
Precautions P.52B-28and Air Bag Module
Clock Spring P.52B-329.
⦆
After the installation, perform a calibration for
the ASC-ECU to learn the steering wheel sensor
neutral point. (Refer to GROUP 35C, On-vehicle
Service - Steering Wheel Sensor Calibration P.
35C-192.)
Pre-removal operation
⦆
Air Bag Module and Steering Wheel Assembly
Removal (Refer to P.37-20.)
⦆
Bottom Cover Assembly (Driver’s seat) and Side
Lower Panel Assembly Removal (Refer to
GROUP 52A - Instrument Panel Assembly
Removal and Installation P.52A-2.)
⦆
Lower side cover (L) Removal (Refer to GROUP
52A - Front Floor Console Assembly Removal
and Installation P.52A-8.)
⦆
WCM vehicles with WCM/Receiver Antenna
Module vehicles with KOS Removal (Refer to
GROUP 54Ag, Ignition Switch - On-vehicle
Service - Ignition Switch Removal and
Installation P.54Ag-13.)
Post-installation operation
⦆
WCM vehicles with WCM/Receiver Antenna
Module vehicles with KOS Installation (Refer to
GROUP 54Ag, Ignition Switch - On-vehicle
Service - Ignition Switch Removal and
Installation P.54Ag-13.)
⦆
Lower side cover (L) Installation (Refer to
GROUP 52A - Front Floor Console Assembly
Removal and Installation P.52A-8.)
⦆
Bottom Cover Assembly (Driver’s seat) and Side
Lower Panel Assembly Installation (Refer to
GROUP 52A - Instrument Panel Assembly
Removal and Installation P.52A-2.)
⦆
Air Bag Module and Steering Wheel Assembly
Installation (Refer to P.37-20.)
POWER STEERING
37-23
STEERING SHAFT
⦆
Confirm that the steering wheel is at the straight-
ahead position.
⦆
Steering wheel sensor calibration (Refer to
GROUP 35C, On-vehicle Service - Steering
Wheel Sensor Calibration P.35C-192.)
ZC5018370000
A
A
5
9
3
2
6
7
1
8
4
10
Section A-A
Claw
Column
Cover
2.5 ± 0.5 N·m
22.1 ± 4.4 in-lb
2.5 ± 0.5 N·m
22.1 ± 4.4 in-lb
2.5 ± 0.5 N·m
22.1 ± 4.4 in-lb
7.0 ± 3.0 N·m
61 ± 26 in-lb
12 ± 3 N·m
102 ± 26 in-lb
20 ± 5 N·m
15 ± 3 ft-lb
28 ± 7 N·m
21 ± 5 ft-lb
Removal steps
<<A>>
1.
Knob cap <Vehicles with KOS>
2.
Ignition key cover
3.
Steering column lower cover
4.
Steering column protector
5.
Steering column upper cover
6.
Paddle shift assembly vehicles with
paddle shift
>>B<<
7.
Steering wheel sensor/clock spring
column switch assembly (Refer to
GROUP 35C - Steering Angle
Sensor P.35C-198and GROUP 52B -
Driver side·passenger side air bag
module clock spring P.52B-329.)
Removal steps
8.
Key interlock cable (Refer to GROUP
23A - A/T Key Interlock And Shiftlock
Mechanisms P.23A-168.)
<<B>>
9.
Steering shaft cover
<<C>>
>>A<<
10. Steering column shaft assembly
37-24
POWER STEERING
STEERING SHAFT
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст