Mitsubishi Outlander XL. Manual — part 971

STEP 3. Recheck for diagnostic trouble code.
Check again if the DTC is set to the combination meter.

(1)

Erase the DTC.

(2)

Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.

(3)

Check if DTC is set.

(4)

Turn the ignition switch to the "LOCK" (OFF) position.

Q:Is the DTC set?

YES:

Replace the combination meter.

NO:

The trouble can be an intermittent malfunction (Refer

to GROUP 00 - How to use Troubleshooting/inspection
Service Points - How to Cope with Intermittent
Malfunction P.00-15).

DTC U0245: Audio visual navigation unit CAN timeout

M15410100106USA0000010000

｠

If DTC U0245 is set, be sure to diagnose the CAN
bus line.

｠

When replacing the ECU, always check that the
communication circuit is normal.

DIAGNOSTIC FUNCTION
When the signals from audio visual navigation unit
cannot be received, the combination meter sets DTC
U0245.

JUDGMENT CRITERIA
With the ignition switch in the ON position, system
voltage between 10 - 16 volts (data from ETACS-

ECU), power supply fuse is OK, or odometer value is
80.5 km (50 miles) or more, and the communications
with audio visual navigation unit cannot be
established for 2,500 ms or more, the combination
meter determines that a problem has occurred.

TROUBLESHOOTING HINTS

｠

The CAN bus line may be defective.

｠

The combination meter may be defective.

｠

The audio visual navigation unit may be defective.

DIAGNOSIS

Required Special Tools:

｠

MB991958: Scan Tool (M.U.T.-III Sub Assembly)

｠

MB991824: Vehicles Communication Interface (V.C.I.)

｠

MB991827: M.U.T.-III USB Cable

｠

MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)

COMBINATION METER

54Ab-37

DIAGNOSIS

STEP 1. Using scan tool MB991958, diagnose the CAN bus
line.

ZC501967

AC404789

ZC5019680000

MB991824

MB991827

MB991910

Data link

connector

To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.

(1)

Connect scan tool MB991958. Refer to "How to connect the
Scan Tool (M.U.T.-III) P.54Ab-5."

(2)

Turn the ignition switch to the "ON" position.

(3)

Diagnose the CAN bus line.

(4)

Turn the ignition switch to the "LOCK" (OFF) position.

Q:Is the CAN bus line found to be normal?

YES:

Go to Step 2.

NO:

Repair the CAN bus line. (Refer to GROUP 54D,

Diagnosis P.54D-17).

STEP 2. Using scan tool MB991958, read the audio visual
navigation unit diagnostic trouble code.
Check if DTC is set to the audio visual navigation unit.

Q:Is the DTC set?

YES:

Troubleshoot the MMCS. Refer to GROUP 54B, Diagnosis

<MMCS>.

NO:

Go to Step 3.

STEP 3. Recheck for diagnostic trouble code.
Check again if the DTC is set to the combination meter.

(1)

Erase the DTC.

(2)

Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.

(3)

Check if DTC is set.

(4)

Turn the ignition switch to the "LOCK" (OFF) position.

Q:Is the DTC set?

YES:

Replace the combination meter.

NO:

The trouble can be an intermittent malfunction (Refer

to GROUP 00 - How to use Troubleshooting/inspection
Service Points - How to Cope with Intermittent
Malfunction P.00-15).

DTC U1415: Coding not completed/Data fail

M15410100062USA0000010000

｠

If DTC U1415 is set, diagnose the CAN bus lines.

｠

When replacing the ECU, always check that the
communication circuit is normal.

54Ab-38

COMBINATION METER

DIAGNOSIS

DIAGNOSTIC FUNCTION
If the vehicle information data is not registered to the
combination meter, the combination meter sets DTC
U1415.

JUDGMENT CRITERIA
With the global coding counter value "0," if all the
global coding data (vehicle information) are not

stored, the combination meter determines that a
problem has occurred.

TROUBLESHOOTING HINTS

｠

The CAN bus line may be defective.

｠

The combination meter may be defective.

｠

The ETACS-ECU may be defective.

DIAGNOSIS

Required Special Tools:

｠

MB991958: Scan Tool (M.U.T.-III Sub Assembly)

｠

MB991824: Vehicles Communication Interface (V.C.I.)

｠

MB991827: M.U.T.-III USB Cable

｠

MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)

STEP 1. Using scan tool MB991958, diagnose the CAN bus
line.

ZC501967

AC404789

ZC5019680000

MB991824

MB991827

MB991910

Data link

connector

To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.

(1)

Connect scan tool MB991958. Refer to "How to connect the
Scan Tool (M.U.T.-III) P.54Ab-5."

(2)

Turn the ignition switch to the "ON" position.

(3)

Diagnose the CAN bus line.

(4)

Turn the ignition switch to the "LOCK" (OFF) position.

Q:Is the CAN bus line found to be normal?

YES:

Go to Step 2.

NO:

Repair the CAN bus line. (Refer to GROUP 54D,

Diagnosis P.54D-17).

STEP 2. Using scan tool MB991958, read the ETACS-ECU
diagnostic trouble code.
Check if DTC is set to the ETACS-ECU.

Q:Is the DTC set?

YES:

Troubleshoot the ETACS-ECU. Refer to GROUP 54Ad,

Diagnosis P.54Ad-8.

NO:

Go to Step 3.

STEP 3. Recheck for diagnostic trouble code.
Check again if the DTC is set to the combination meter.

(1)

Erase the DTC.

COMBINATION METER

54Ab-39

DIAGNOSIS

(2)

Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.

(3)

Check if DTC is set.

(4)

Turn the ignition switch to the "LOCK" (OFF) position.

Q:Is the DTC set?

YES:

Replace the combination meter.

NO:

The trouble can be an intermittent malfunction (Refer

to GROUP 00 - How to use Troubleshooting/inspection
Service Points - How to Cope with Intermittent
Malfunction P.00-15).

TROUBLE SYMPTOM CHART

M15410100026USA0000010000

｠

During troubleshooting, a DTC code associated
with other system may be set when the ignition
switch is turned on with connector(s)
disconnected. On completion, confirm all
systems for DTC code(s). If DTC code(s) are set,
erase them all.

｠

When the combination meter is required to be
replaced as a result of the troubleshooting, the
current driving distance and number of elapsed
days to be used for service reminder function
must be entered into the meter after the
replacement. Therefore, read "Integrated
mileage for reminder," "Integrated days for
reminder," "Mileage until Extra reminder,"
"Months until Extra reminder," and "Current

Schedule" from the meter before the
replacement using the special function of scan
tool MB991958, and note them. For the
operation method of scan tool MB991958, refer
to P.54Ab-70. If "Integrated mileage for
reminder" or "Integrated days for reminder"
cannot be read by the scan tool MB991958,
follow the method described below.

For the driving distance for check warning,
use the driving distance displayed on the
multi information display.

For the elapsed days for check warning,
calculate the number of elapsed days from
the delivery date to the customer (service
remainder function start date) and current
date.

Trouble symptom

Inspection
Procedure
No.

Reference
page

Power supply circuit check.

54Ab-41

The speedometer does not work (the other meters work).

54Ab-46

The tachometer does not work (the other meters work).

54Ab-47

Tone alarm does not sound normally.

54Ab-49

The combination meter light does not illuminate normally or the multi information
display is not displayed normally.