Mitsubishi L200 (2018 year). Instruction — part 24
2. Turn the bulb socket anticlockwise to re-
move it. And remove the bulb from the
socket by turning it anticlockwise while
pressing in.
3. To install the bulb, perform the removal
steps in reverse.
Front fog lamps* / Daytime
running lamps*
E01004003469
1. Insert a straight blade (or minus) screw-
driver with a cloth over its tip at the edge
of the cover (A) and pry gently to re-
move the cover.
2. Remove the 3 screws (B) and remove
the lamp unit.
NOTE
l
When unfastening the screws of the fog
lamp, be careful not to mistakenly move the
beam position adjustment screw (C).
3. Turn the socket anticlockwise to remove
it.
Type 1
Type 2
Type 3
D- Front fog lamp
E- Daytime running lamp
Replacement of lamp bulbs
10-27
OKTE18E1
Maintenance
10
4. While holding down the tab (F), pull out
the bulb (G).
Front fog lamp
Daytime running lamp
5. To install the bulb, perform the removal
steps in reverse.
Rear combination lamps
E01004202884
1. Open the rear gate.
(Refer to “Rear gate” on page 3-20.)
2. Remove the screws (A) that hold the
lamp unit.
3. Move the lamp unit towards the rear of
the vehicle and remove the clips (B).
4. Remove each socket and bulb assembly
by turning it anticlockwise.
C-
Tail and stop lamp
Remove the bulb from the sock-
et by turning it anticlockwise
while pressing in.
D-
Rear turn-signal lamp
Remove the bulb by pulling it
out.
E-
Rear fog lamp (driver’s side)*/
Reversing lamp
Remove the bulb by pulling it
out.
5. To install the bulb, perform the removal
steps in reverse.
Replacement of lamp bulbs
10-28
OKTE18E1
Maintenance
10
NOTE
l
When mounting the lamp unit, align the pins
(F) and clip (G) on the lamp unit with the
holes (H) in the body.
Licence plate lamps
E01004602224
1. Insert a straight blade (or minus) screw-
driver into the lamp assembly and pry
gently to remove it.
NOTE
l
Wrap a piece of cloth around the tip of the
screwdriver in order to avoid scratching the
lens and the body.
2. Remove the socket and bulb assembly
together by turning it anticlockwise, and
then remove the bulb by pulling it out.
3. To install the bulb, perform the removal
steps in reverse.
Replacement of lamp bulbs
10-29
OKTE18E1
Maintenance
10
NOTE
l
When mounting the lamp unit, put the hook
(A) on the right side of the lamp unit into the
body first.
Front room & map lamps*
E01010501074
1. Insert a straight blade (or minus) screw-
driver into the notch of the lens and pry
gently to remove it.
Remove the bulb from the lamp holder.
NOTE
l
Wrap a piece of cloth around the tip of the
screwdriver in order to avoid scratching the
lens.
2. To install the bulb, perform the removal
steps in reverse.
NOTE
l
When installing the lens, align the 2 tabs on
the lens with the holes on the vehicle side.
Rear room lamp
E01004901464
Type 1
1. Insert a straight blade (or minus) screw-
driver into the notch of the lens and pry
gently to remove it. Remove the bulb
from the lamp holder.
NOTE
l
Wrap a piece of cloth around the tip of the
screwdriver in order to avoid scratching the
lens.
2. To install the bulb, perform the removal
steps in reverse.
NOTE
l
When installing the lens, align the 2 tabs on
the lens with the holes on the vehicle side.
Replacement of lamp bulbs
10-30
OKTE18E1
Maintenance
10
NOTE
l
When installing the lens, fit the two tabs on
one side of the lens into the holes on the ve-
hicle side before fitting the two tabs on the
opposite side of the lens into the holes on the
vehicle side.
Type 2
1. Insert a straight blade (or minus) screw-
driver into the notch of the lens and pry
gently to remove it. Remove the bulb
from the lamp holder.
NOTE
l
Wrap a piece of cloth around the tip of the
screwdriver in order to avoid scratching the
lens.
2. To install the bulb, perform the removal
steps in reverse.
NOTE
l
When installing the lens, fit the two tabs on
one side of the lens into the holes on the ve-
hicle side before fitting the two tabs on the
opposite side of the lens into the holes on the
vehicle side.
Glove box lamp
E01006101516
Have the glove box lamp bulb replaced at a
MITSUBISHI MOTORS Authorized Service
Point.
Masking the headlamps
E01011601085
When entering a country in which vehicles
are driven on the opposite side of the road to
the country in which your vehicles is sup-
plied, necessary measures have to be taken to
avoid dazzling oncoming traffic.
Masking the headlamps
10-31
OKTE18E1
Maintenance
10
High intensity discharge head-
lamp type
Do not need any adjustment.
Halogen headlamp type
Mask the headlamps according to the next
procedure.
1. Turn the headlamp off and wait until the
headlamps got cold.
2. According to the illustrations, prepare
the sticker (A) to stick the headlamp sur-
face of right and left.
NOTE
l
Use a sticker with a light blocking effect
enough.
Using of a sticker without a light blocking
effect will not acquire a blocking effect.
3. Seeing from the headlamp front, position
(C) of the sticker and the central mark
(B) of the headlamp and stick a sticker
along the vertical dotted line.
NOTE
l
Align the vertical dotted line with the line of
the reflector in the headlamp.
LHD
Left lens
Right lens
115mm
105mm
37mm
50mm
RHD
Left lens
Right lens
105mm
37mm
50mm
115mm
Masking the headlamps
10-32
OKTE18E1
Maintenance
10
Vehicle labeling. . . . . . . . . . . . . . . . . . . . 11-02
Vehicle dimensions. . . . . . . . . . . . . . . . . . ... 11-04
Vehicle performance. . . . . . . . . . . . . . . . . . . 11-10
Vehicle weight. . . . . . . . . . . . . . . . . . . . .. 11-10
Engine specifications. . . . . . . . . . . . . . . . . . 11-14
Electrical system. . . . . . . . . . . . . . . . . . . ... 11-15
Tyres and wheels. . . . . . . . . . . . . . . . . . . ...11-15
Fuel consumption. . . . . . . . . . . . . . . . . . . ..11-16
Capacity. . . . . . . . . . . . . . . . . . . . . . . 11-17
Specifications
OKTE18E1
11
Vehicle labeling
E01100105005
Vehicle Identification Number:
(VIN)
The vehicle identification number is stamped
as shown in the illustration.
Vehicle identification number
plate (RHD vehicles only)
The vehicle identification number is stamped
on the plate riveted to the left front corner of
the vehicle body. It is visible from outside of
the vehicle through the windscreen.
Vehicle information code plate
E01102200034
The vehicle information code plate is located
as shown in the illustration.
The plate shows model code, engine model,
transmission model and body colour code,
etc.
Please use this number when ordering re-
placement parts.
Vehicle labeling
11-02
OKTE18E1
Specifications
11
1- Model code
2- Engine model code
3- Transmission model code
4- Final gear ratio
5- Body colour code
6- Interior code
7- Option code
Engine model/number
E01102500125
The engine model and number are stamped
on the engine cylinder block as shown in the
illustrations.
Vehicle labeling
11-03
OKTE18E1
Specifications
11
Vehicle dimensions
E01100204692
Single cab
Vehicle dimensions
11-04
OKTE18E1
Specifications
11
Single cab
1
Front track
1,520 mm
2
Overall width
1,785 mm
3
Front overhang
865 mm
4
Wheel base
3,000 mm
5 Rear overhang
Without rear bumper
1,215 mm
With rear bumper
1,295 mm
6
Overall length
Without rear bumper
5,080 mm
With rear bumper
5,160 mm
7
Ground clearance (unladen)
200 mm
8
Overall height (unladen)
1,780 mm
9
Rear track
1,515 mm
10 Cargo bed length
2,265 mm
11 Cargo bed width
1,470 mm
12 Cargo bed height
845 mm
Minimum turning radius
Body
6.3 m
Wheel
5.9 m
Vehicle dimensions
11-05
OKTE18E1
Specifications
11
Club cab
Vehicle dimensions
11-06
OKTE18E1
Specifications
11
Club cab
1
Front track
1,520 mm
2
Overall width
1,785 mm, 1,815 mm
*
3
Front overhang
865 mm
4
Wheel base
3,000 mm
5 Rear overhang
Without rear bumper
1,330 mm
With rear bumper
1,410 mm
6
Overall length
Without rear bumper
5,195 mm
With rear bumper
5,275 mm
7
Ground clearance (unladen)
200 mm, 205 mm
*
8
Overall height (unladen)
1,775 mm, 1,780 mm
*
9
Rear track
1,515 mm
10 Cargo bed length
1,850 mm
11 Cargo bed width
1,470 mm
12 Cargo bed height
845 mm, 850 mm
*
*
: Vehicles with wide fender
NOTE
l
The vehicle overall length and height may vary depending on the equipment installed.
Minimum turning radius
Body
6.3 m
Vehicle dimensions
11-07
OKTE18E1
Specifications
11
Wheel
5.9 m
Double cab
Vehicle dimensions
11-08
OKTE18E1
Specifications
11
Double cab
1
Front track
1,520 mm
2
Overall width
1,785 mm, 1,815 mm
*
3
Front overhang
865 mm
4
Wheel base
3,000 mm
5 Rear overhang
Without rear bumper
1,340 mm
With rear bumper
1,420 mm
6
Overall length
Without rear bumper
5,205 mm
With rear bumper
5,285 mm
7
Ground clearance (unladen)
200 mm, 205 mm
*
8
Overall height (unladen)
1,775 mm, 1,780 mm
*
9
Rear track
1,515 mm
10 Cargo bed length
1,520 mm
11 Cargo bed width
1,470 mm
12 Cargo bed height
845 mm, 850 mm
*
*
: Vehicles with wide fender
Minimum turning radius
Body
6.3 m
Wheel
5.9 m
Vehicle dimensions
11-09
OKTE18E1
Specifications
11
Vehicle performance
E01100304071
Single cab
Maximum speed
169 km/h (105 mph)
Club cab
Item
Vehicles without wide fender
Vehicles with wide fender
Maximum speed
169 km/h (105 mph)
179 km/h (111 mph)
Double cab
Item
Vehicles without wide
fender
Vehicles with wide fender
M/T
A/T
Maximum speed
169 km/h (105 mph)
174 km/h, 179 km/h
*
173 km/h, 177 km/h
*
*
: Vehicles with high power engine
Vehicle weight
E01100408650
Single cab
Kerb weight
Without optional parts
1,790 kg
With full optional parts
1,835 kg
Maximum gross vehicle weight
2,850 kg
Maximum axle weight
Front
1,260 kg
Vehicle performance
11-10
OKTE18E1
Specifications
11
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст