Mitsubishi Montero (2004+). Manual — part 525
COMBINATION METER ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-69
STEP 7. Measure at combination meter connector D-32 in
order to check the ground circuit to the combination
meter.
(1) Disconnect combination meter connector D-32, and
measure at the wiring harness side.
(2) Measure the resistance between terminal 25 and ground.
• The resistance should equal 2 ohms or less.
(3) Measure the resistance between terminal 11 and ground.
• The resistance should equal 2 ohms or less.
Q: Is the measured voltage approximately 12 volts (battery
positive voltage)?
YES : Repair the combination meter. Check to see that all
meters operate.
NO : Go to Step 8.
STEP 8. Check combination meter connector D-32 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is combination meter connector D-32 in good
condition?
YES : Go to Step 9.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Check to see that all meters operate.
AC204170
CONNECTOR : D-32
CU
HARNESS SIDE
D-32(GR)
D-32(GR)
3
4
16
17
1
2
14
15
5
7 6
19
13
8
9
21
22
20
18
23
10
11
24
25
12
AC204738 EP
HARNESS SIDE: D-32
3
4
16
17
1
2
14
15
5
7 6
19
13
8
9
21
22
20
18
23
10
11
24
25
12
AC204170
CONNECTOR : D-32
CU
HARNESS SIDE
D-32(GR)
D-32(GR)
3
4
16
17
1
2
14
15
5
7 6
19
13
8
9
21
22
20
18
23
10
11
24
25
12
COMBINATION METER ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-70
STEP 9. Check the wiring harness between combination
meter connector D-32 (terminal 25 and 11) and ground.
Q: Is the wiring harness between combination meter
connector D-32 (terminal 25 and 11) and ground in good
condition?
YES : There is no action to be taken.
NO : Repair the wiring harness. Check to see that all
meters operate.
AC204170
CONNECTOR : D-32
CU
HARNESS SIDE
D-32(GR)
D-32(GR)
3
4
16
17
1
2
14
15
5
7 6
19
13
8
9
21
22
20
18
23
10
11
24
25
12
COMBINATION METER ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-71
SPECIAL TOOLS
M1543000601878
TOOL
TOOL NUMBER
AND NAME
SUPERSESSION
APPLICATION
MB991958
A: MB991824
B: MB991827
C: MB991910
D: MB991911
E: MB991914
F: MB991825
G: MB991826
MUT-III sub assembly
A: Vehicle
communication
interface (V.C.I.)
B: MUT-III USB cable
C: MUT-III main
harness A
(Vehicles with CAN
communication
system)
D: MUT-III main
harness B
(Vehicles without
CAN
communication
system)
E: MUT-III main
harness C (for
Daimler Chrysler
models only)
F: MUT-III
measurement
adapter harness
G: MUT-III trigger
harness
MB991824-KIT
NOTE: MB991826
MUT-III trigger harness
is not necessary when
pushing V.C.I. ENTER
key.
Reading MFI system
diagnostic trouble code
CAUTION
MUT-III main harness B
(MB991911) should be
used. MUT-III main
harness A and C
should not be used for
this vehicle.
MB991910
MB991826
MB991958
MB991911
MB991914
MB991824
MB991827
MB991825
A
B
C
D
E
F
G
DO NOT USE
DO NOT USE
COMBINATION METER ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-72
ON-VEHICLE SERVICE
SPEEDOMETER CHECK
M1543000900490
Adjust the pressure of tires to the specified level (Refer to
GROUP 31, On-vehicle Service
CAUTION
Place the transfer shift lever to "2H" position.
1. Set the vehicle onto a speedometer tester and use wheel
chocks to hold the front wheels.
2. To prevent the sideward shaking of the front wheel, attach
the puller on the towing hook and the tie down hook at front
side and connect its both ends to the anchor plate.
3. To prevent the jumping out of the vehicle, attach the chain
and the wire whose both ends are tightly fixed to the rear
towing hook.
CAUTION
Do not increase/decrease speed rapidly while testing.
MB991223
A: MB991219
B: MB991220
C: MB991221
D: MB991222
Harness set
A: Test harness
B: LED harness
C: LED harness
adapter
D: Probe
General service tool
(jumper)
Making voltage and
resistance
measurements during
troubleshooting
A: Connect pin contact
pressure inspection
B: Power circuit
inspection
C: Power circuit
inspection
D: Commercial tester
connection
TOOL
TOOL NUMBER
AND NAME
SUPERSESSION
APPLICATION
MB991223
A
B
C
D
AC
ACX01629AB
ACX00775 AB
FRONT
ANCHOR PLATE
PULLER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст