Mitsubishi Montero (2004+). Manual — part 1227
AIR BAG MODULE AND SEAT BELT PRE-TENSIONER DISPOSAL PROCEDURES
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-243
WARNING
•
Before deployment, check carefully to be sure that
no one is nearby.
•
The inflator will be quite hot immediately following
the deployment, so wait at least 30 minutes to
allow it to cool before attempting to handle it.
Although not poisonous, do not inhale gas from
air bag deployment. See Deployed Air Bag Module
and Operated Seat Belt Pre-tensioner Disposal
(Refer to
) for post-deployment handling
instructions.
•
If the air bag fails to deploy, do not go near the
module. Contact the MMNA Teach Line.
9. At a location as far away from the air bag module as
possible, and from a shielded position, disconnect the two
connected wires from each other, and connect them, to the
two terminals of the battery (which has been removed from
the vehicle) to deploy the air bag.
10.Discard the deployed air bag module as specified in
Deployed Air Bag Module and Operated Seat Belt
Pre-tensioner Disposal (Refer to
.
DEPLOYMENT OUTSIDE THE VEHICLE <AIR BAG
MODULE (FRONT PASSENGER'S SIDE)>
DANGER
Wait at least 60 seconds after disconnecting the bat-
tery cables before doing any further work (Refer to
).
WARNING
•
Battery posts, terminals and related accessories
contain lead and lead compounds. WASH HANDS
AFTER HANDLING.
•
Deploy the air bag in a wide, flat area at least 6
meters (20 feet) away from obstacles and other
people.
•
Do not perform deployment outside if a strong
wind is blowing. If there is a slight breeze, place
the air bag module downwind from the battery.
1. Disconnect the negative (
−) and positive (+) battery cables
from the battery terminals, and then remove the battery from
the vehicle.
ACX01315
DEPLOYMENT WIRES
AB
AIR BAG MODULE AND SEAT BELT PRE-TENSIONER DISPOSAL PROCEDURES
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-244
CAUTION
Once disconnected, both electrodes of the front passen-
ger’s air bag module connector short automatically to pre-
vent accidental deployment caused by static etc. Still, in
consideration of the accidental deployment, store the air
bag module on flat place with deployment surface facing
up. Also, do not put anything on it.
2. Remove the air bag module from the vehicle (Refer to
3. Connect two wires, each 6 meters (20 feet) or longer, to the
two leads of special tool MB686560, and cover the
connections with insulation tape. The other ends of the two
wires should be connected to each other (short-circuited), to
prevent sudden unexpected deployment of the air bag
module.
4. Connect the deployment wires to special tool MB686560,
pass it beneath the tire and wheel assembly, and connect it
to the air bag module.
CAUTION
• The adapter harness below the wheel should be loose.
If it is too tight, the reaction when the air bag deploys
could damage the adapter harness.
• During deployment, the connector of special tool
MB686560 must not be between the tires.
5. Pass the thick wire through the air bag module mounting
hole, and then secure the air bag module to an old tire with a
wheel in it so that the pad on the module is facing upwards.
6. Place three old tires without wheels on top of the tire
secured to the air bag module, and secure all tires together
with ropes (four locations).
AC001932
CONNECTION
DEPLOYMENT WIRES
MR686560
INSULATOR TAPE
6 m (20 ft)
LONG OR
MORE
AB
AC100483
DEPLOYMENT WIRES
FRONT PASSENGER'S AIR BAG MODULE
AB
ACX00611
TIRES WITHOUT
WHEELS
DEPLOYMENT
WIRES
AB
AIR BAG MODULE AND SEAT BELT PRE-TENSIONER DISPOSAL PROCEDURES
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-245
WARNING
•
Before deployment, check carefully to be sure that
no one is nearby.
•
The inflator will be quite hot immediately following
the deployment, so wait at least 30 minutes to
allow it to cool before attempting to handle it.
Although not poisonous, do not inhale gas from
air bag deployment. See Deployed Air Bag Module
and Operated Seat Belt Pre-tensioner Disposal
(Refer to
) for post-deployment handling
instructions.
•
If the air bag fails to deploy, do not go near the
module. Contact the MMNA Tech Line.
7. At a location as far away from the air bag module as
possible, and from a shielded position, disconnect the two
connected wires from each other, and connect them to the
two terminals of the battery (which has been removed from
the vehicle) to deploy the air bag.
8. Discard the deployed air bag module as specified in
Deployed Air Bag Module and Operated Seat Belt
Pre-tensioner Disposal (Refer to
.
DEPLOYMENT OUTSIDE VEHICLE <SIDE-AIRBAG
MODULE>
DANGER
Wait at least 60 seconds after disconnecting the bat-
tery cables before doing any further work (Refer to
).
WARNING
•
Battery posts, terminals and related accessories
contain lead and lead compounds. WASH HANDS
AFTER HANDLING.
•
Deploy the air bag in a wide, flat area at least 6
meters (20 feet) away from obstacles and other
people.
•
Do not perform deployment outside if a strong
wind is blowing. If there is a slight breeze, place
the air bag module downwind from the battery.
1. Disconnect the negative (
−) and positive (+) battery cables
from the battery terminals, and then remove the battery from
the vehicle.
2. Remove the front seatback assembly with side-airbag
module from the vehicle (Refer to GROUP 52A, Front Seat
ACX01315
DEPLOYMENT WIRES
AB
AIR BAG MODULE AND SEAT BELT PRE-TENSIONER DISPOSAL PROCEDURES
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-246
CAUTION
Once disconnected, both electrodes of the side air bag
module connector short automatically to prevent acciden-
tal deployment caused by static etc. Still, in consideration
of the accidental deployment, store the air bag module on
flat place with deployment surface facing up. Also, do not
put anything on it.
3. Connect two wires, each 6 meters (20 feet) or longer, to the
two leads of special tool MB686560, and cover the
connections with insulation tape. The other ends of the two
wires should be connected to each other (short-circuited), to
prevent sudden unexpected deployment of the air bag
module.
4. Place the front seatback assembly with its back contact with
the ground.
5. Connect the SRS air bag adapter harness with the
deployment wires to the side air bag module connector.
WARNING
•
Before deployment, check carefully to be sure that
no one is nearby.
•
The inflator will be quite hot immediately following
the deployment, so wait at least 30 minutes to
allow it to cool before attempting to handle it.
Although not poisonous, do not inhale gas from
air bag deployment. See Deployed Air Bag Module
and Operated Seat Belt Pre-tensioner Disposal
(Refer to
) for post-deployment handling
instructions.
•
If the air bag fails to deploy, do not go near the
module. Contact the MMNA Tech Line.
6. Disconnect the deployment wires as far from the front
seatback assembly possible and connect the harnesses to
the battery removed from the vehicle. Then, deploy.
7. Remove the deployed air bag module from the seatback
assembly and discard as specified in the Deployed air bag
module and Operated Seat Belt Pre-tensioner (Refer to
.
AC001932
CONNECTION
DEPLOYMENT WIRES
MR686560
INSULATOR TAPE
6 m (20 ft)
LONG OR
MORE
AB
ACX00612AB
MB686560
FRONT SEATBACK
ASSEMBLY
ACX01316
DEPLOYMENT
WIRES
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст