Mitsubishi Montero (2004+). Manual — part 765
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-317
DIAGNOSIS
Required Special Tool:
• MB991223: Harness Set
STEP 1. Verify the operation of each light.
Q: Which light does not illuminate?
Taillight (LH), license plate light and side marker light
(LH) : Go to Step 2.
Taillight (RH) and side marker light (RH) : Go to Step 4.
Taillight (LH) and license plate : Go to Step 6.
Position light : Go to Step 8.
Position light (LH) : Go to Step 11.
Position light (RH) : Go to Step 17.
Taillights : Go to Step 23.
Taillight (LH) : Go to Step 26.
Taillight (RH) : Go to Step 32.
License plate lights : Go to Step 38.
Side marker light (LH) : Go to Step 44.
Side marker light (RH) : Go to Step 50.
All lights : Refer to Inspection Procedure J-1 "Tail lights do
not illuminate
STEP 2. Check rear combination light (LH) connector G-02
and front-ECU connector A-07X for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
Q: Are rear combination light (LH) connector G-02 and
front-ECU connector A-07X in good condition?
YES : Go to Step 3.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the taillight (LH), license plate
light and side marker light (LH) illuminates normally.
AC204183
CONNECTOR : A-07X
AB
2 1
3
4
6
7
8
9
5
11 10
RELAY BOX SIDE
AC204179
CONNECTOR : G-02
AB
HARNESS SIDE
G-02(B)
G-02(B)
1
4
2
3
5
6
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-318
STEP 3. Check the wiring harness between rear
combination light (LH) connector G-02 (terminal 1) and
front-ECU connector A-07X (terminal 8).
NOTE: Also check intermediate connectors D-28 and D-125 for
loose, corroded, or damaged terminals, or terminals pushed
back in the connector. If intermediate connector D-28 or D-125
is damaged, repair or replace the damaged component(s) as
described in GROUP 00E, Harness Connector Inspection
.
Q: Is the wiring harness between rear combination light
(LH) connector G-02 (terminal 1) and front-ECU
connector A-07X (terminal 8) in good condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the taillight (LH), license plate light and side marker
light (LH) illuminates normally.
AC204183
CONNECTOR : A-07X
AB
2 1
3
4
6
7
8
9
5
11 10
RELAY BOX SIDE
AC204179
CONNECTOR : G-02
AB
HARNESS SIDE
G-02(B)
G-02(B)
1
4
2
3
5
6
AC204188
CONNECTORS : D-28, D-125
AP
D-28
D-28
D-125
D-125
2 3
27
32
28
33
16
15
4 5
19
18
29
17
34
7 8
35
22
21
9 10
30
36
31
37
25
24
23
6
20
1
14
26
11
13
12
38
9
8
6 7
5
3 4
20
32
21
33
43
17 18
30
41
16
29
28
39 40
13
25
12
24
35 36
14
26
37
15
27
38
19
31
42
1
10
22
2
11
23
34
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-319
STEP 4. Check rear combination light (RH) connector G-09
and front-ECU connector A-07X for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
Q: Are rear combination light (RH) connector G-09 and
front-ECU connector A-07X in good condition?
YES : Go to Step 5.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the taillight (RH) and side marker
light (RH) illuminates normally.
STEP 5. Check the wiring harness between rear
combination light (RH) connector G-09 (terminal 1) and
front-ECU connector A-07X (terminal 8).
AC204183
CONNECTOR : A-07X
AB
2 1
3
4
6
7
8
9
5
11 10
RELAY BOX SIDE
AC204179
CONNECTOR : G-09
AC
HARNESS SIDE
G-09(B)
G-09(B)
1
4
2
3
5
6
AC204183
CONNECTOR : A-07X
AB
2 1
3
4
6
7
8
9
5
11 10
RELAY BOX SIDE
AC204179
CONNECTOR : G-09
AC
HARNESS SIDE
G-09(B)
G-09(B)
1
4
2
3
5
6
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-320
NOTE: Also check intermediate connectors D-28 and D-111 for
loose, corroded, or damaged terminals, or terminals pushed
back in the connector. If intermediate connector D-28 or D-111
is damaged, repair or replace the damaged component(s) as
described in GROUP 00E, Harness Connector Inspection
.
Q: Is the wiring harness between rear combination light
(RH) connector G-09 (terminal 1) and front-ECU
connector A-07X (terminal 8) in good condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the taillight (RH) and side marker light (RH)
illuminates normally.
STEP 6. Check taillight (LH) connector G-16 and front-ECU
connector A-07X for loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Q: Are taillight (LH) connector G-16 and front-ECU
connector A-07X in good condition?
YES : Go to Step 7.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the taillight (RH) and side marker
light (RH) illuminates normally.
AC204170
CONNECTOR : D-28
AI
2 3
27
32
28
33
16
15
4 5
19
18
29
17
34
7 8
35
22
21
9 10
30
36
31
37
25
24
23
6
20
1
14
26
11
13
12
38
AC204171
CONNECTOR : D-111
BH
9
8
6 7
5
3 4
20
32
21
33
43
17 18
30
41
16
29
28
39 40
13
25
12
24
35 36
14
26
37
15
27
38
19
31
42
1
10
22
2
11
23
34
AC204183
CONNECTOR : A-07X
AB
2 1
3
4
6
7
8
9
5
11 10
RELAY BOX SIDE
AC204179
CONNECTOR : G-16
AH
HARNESS SIDE
G-16(B)
G-16(B)
3
4
2
1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст