Mitsubishi Montero (2004+). Manual — part 619
ON-VEHICLE SERVICE
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-119
• Engine coolant temperature: 80 − 90 °C (176 − 194 °F)
• Lights, electric cooling fan and accessories: Set to OFF
• Transmission: "N" or "P" position
• Steering wheel: Straightforward
2. Check whether or not the idling speed is the standard value.
Standard value: 700
± 50 r/min
NOTE: There is no necessity to make an adjustment,
because the idling speed is automatically adjusted by the
idle speed control system. If, however, there occurs a devia-
tion from the standard value for some reason, check the idle
speed control system. Refer to GROUP 11A, On-vehicle
Service
3. When the A/C is running after turning the A/C switch to ON,
and the blower switch to the MH or HI position, check to be
sure that the idle speed is at the standard value.
Standard value:
NOTE: It depends on the outside air temperature signal
whether a low load, a middle load or a high load is applied to
the air conditioning. The PCM receives the signal via the
automatic compressor controller and determines whether
the air conditioning is working under high, middle or low
load.
VEHICLE CONDITION
IDLE-UP
SPEED r/min
When the air conditioning is working under
low load (Outside air temperature sensor:
ON)
700
± 50
When the air conditioning is working under
middle load (Outside air temperature
sensor: OFF)
800
± 50
When the air conditioning is working under
high load (Outside air temperature sensor:
OFF)
1,000
± 50
HEATER CONTROL ASSEMBLY, A/C SWITCH AND INSIDE/OUTSIDE CHANGEOVER SWITCH
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-120
HEATER CONTROL ASSEMBLY, A/C SWITCH AND
INSIDE/OUTSIDE CHANGEOVER SWITCH
REMOVAL AND INSTALLATION
M1552012400047
INSTALLATION SERVICE POINTS
.
>>A<< AIR OUTLET CHANGEOVER DAMPER LEVER
CABLE INSTALLATION
1. Set the air outlet changeover control knob on the heater
control assembly to the defroster position.
2. Set the air outlet changeover damper lever of the
heater/cooler unit to the defroster position as shown in the
illustration, and then connect the cable to the link pin.
3. Push the outer cable in the direction of the arrow so that
there is no looseness, and then secure it with the clip.
4. After installation, ensure that each damper operates
smoothly by operating the heater control assembly knob.
.
>>B<< AIR MIX DAMPER LEVER CABLE INSTALLATION
1. Set the temperature control knob on the heater control
assembly to the maximum hot position.
Pre-removal and Post-installation Operation
• Front Driver's Side Under Cover Removal and Installation (Refer to GROUP 52A, Instrument Panel
• Floor Console Removal and Installation (Refer to GROUP 52A, Floor Console
• Foot Duct C and Foot Duct D Removal and Installation (Refer to
.)
AC000934 AB
1
2
3
4
REMOVAL STEPS
1.
CENTER PANEL (REFER TO
GROUP 52A, INSTRUMENT
PANEL
.)
>>B<<
2.
AIR MIX DAMPER LEVER CABLE
>>A<<
3.
AIR OUTLET CHANGEOVER
DAMPER LEVER CABLE
4.
HEATER CONTROL ASSEMBLY
REMOVAL STEPS (Continued)
AC000932 AB
DEFROSTER POSITION
FACE POSITION
HEATER CONTROL ASSEMBLY, A/C SWITCH AND INSIDE/OUTSIDE CHANGEOVER SWITCH
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-121
2. Set the air mix damper lever of the heater/cooler unit to the
maximum hot position as shown in the illustration, and then
connect the cable to the lever pin.
3. Push the outer cable in the direction of the arrow so that
there is no looseness, and then secure it with the clip.
INSPECTION
M1552012500055
DEFROSTER SWITCH CONTINUITY CHECK
Follow the table below to check the defroster switch for continu-
ity.
AC000933 AC
MAXIMUM HOT POSITION
MAXIMUM COOL
POSITION
AIR OUTLET
CHANGEOVER CONTROL
KNOB POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
At the "DEFROSTER" or
"DEFROSTER/FOOT"
position
2
− 3
Less than 2
ohms
At the other positions
1
− 3
Less than 2
ohms
AC001398
HEATER
CONTROL
ASSEMBLY
AB
HEATER CONTROL ASSEMBLY, A/C SWITCH AND INSIDE/OUTSIDE CHANGEOVER SWITCH
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-122
BLOWER SWITCH ASSEMBLY CONTINUITY
CHECK
.
BLOWER SWITCH
Follow the table below to check the blower switch for continuity.
.
A/C SWITCH
Follow the table below to check the A/C switch for continuity.
.
INSIDE/OUTSIDE AIR CHANGEOVER SWITCH
Follow the table below to check the inside/outside air
changeover switch for continuity.
SWITCH
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
0 (OFF)
1
− 3, 3 − 4, 3 − 5, 3 − 6 Open circuit
1 (LO)
3
− 5
Less than 2 ohms
2 (ML)
3
− 1
Less than 2 ohms
3 (MH)
3
− 6
Less than 2 ohms
4 (HI)
3
− 4
Less than 2 ohms
SWITCH
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
OFF
5
− 6
Open circuit
ON
5
− 6
Less than 2 ohms
SWITCH
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
Inside air
4
− 5
Open circuit
Outside air
4
− 5
Less than 2 ohms
AC001399
CONNECTOR A
CONECTOR B
OFF
ON
OFF
ON
A/C SWITCH
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст