Mitsubishi Montero (2004+). Manual — part 750
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-257
.
CIRCUIT OPERATION
The windshield washer switch sends a signal
through the column-ECU (incorporated in the column
switch) to the front-ECU. If the column-ECU sends a
windshield washer switch "ON" signal to the
front-ECU, the front-ECU turns on the relay (incorpo-
rated in the front-ECU), thus causing the windshield
washer motor to be turned on.
.
TECHNICAL DESCRIPTION (COMMENT)
If the windshield washer does not work normally, the
windshield washer motor, the column switch (wind-
shield wiper and washer switch) or the front-ECU
may be defective.
.
TROUBLESHOOTING HINTS
• The windshield washer motor may be defective
• The column switch (windshield wiper and washer
switch) may be defective
• The front-ECU may be defective
• The wiring harness or connectors may have
loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991911: MUT-III Main Harness B
• MB991813: SWS Monitor Kit
• MB991806: SWS Monitor Cartridge
• MB991812: SWS Monitor Harness (For Column-ECU)
• MB991822: Probe Harness
STEP 1. Verify the windshield wiper.
Q: Does the windshield wiper operate normally?
YES : Go to Step 2.
NO : Refer to Inspection Procedure G-1 "Windshield wiper
does not work at all
AC205138
CONNECTOR: A-08X
AB
BATTERY
FRONT-ECU
A-08X
AC205145AB
CONNECTOR: A-33
A-33
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-258
STEP 2. Use scan tool MB991958 to select "ECU COMM
CHK" on the SWS monitor display.
Check the following ECUs:
• Column-ECU
• Front-ECU
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958. Connect
the DLC harness before connecting the column-ECU har-
ness. Be sure to connect SWS monitor kit MB991862 after
turning on scan tool MB991958.
(1) Connect the special tool. Refer to "How to connect SWS
monitor
(2) Connect SWS monitor kit MB991862 to the data link
connector (13-pin).
(3) Turn the ignition switch to the "ON" position.
(4) Operate scan tool MB991958 according to the procedure
below to display "ECU COMM CHECK."
1. Select "SYSTEM SELECT."
2. Select "SWS."
3. Select "SWS MONITOR."
4. Select "ECU COMM CHK".
(5) Scan tool MB991958 should show "OK" on the "ECU
COMM CHK" menus for both the "COLUMN ECU" and the
"FRONT ECU" menus.
Q: Is "OK" displayed on the "COLUMN ECU" and "FRONT
ECU" menu?
"OK" is displayed for all the items : Go to Step 3.
"NG" is displayed on the "COLUMN ECU" menu : Refer
to Inspection Procedure A-2 "Communication with
column switch (column-ECU) is not possible
"NG" is displayed on the "FRONT ECU" menu : Refer to
Inspection procedure A-4 "Communication with
front-ECU is not possible
AC309091
MB991911
MB991827
MB991824
AB
MB991806
MB991862
DATA LINK
CONNECTOR
(16-PIN)
DATA LINK
CONNECTOR
(13-PIN)
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-259
STEP 3. Check the input signal by using "FUNCTION
DIAG." menu of the SWS monitor.
Check the input signals from the following switches:
• Ignition switch: ON
• Windshield washer switch: ON
Operate scan tool MB991958 according to the procedure below
to display "F.WIPER WASH."
1. Select "SYSTEM SELECT."
2. Select "SWS."
3. Select "SWS MONITOR."
4. Select "FUNCTION DIAG."
5. Select "WIPER."
6. Select "F.WIPER WASH."
Check that normal conditions are displayed on the items
described in the table below.
Q: Are normal conditions displayed for "FRONT
WASH.SW" and "FRONT ECU ACK"?
Normal conditions displayed for all the items : Go to
Step 4.
The scan tool does not show the respective normal
condition for item "FRONT WASH. SW" : Replace the
column switch. Verify that the windshield washer
works normally.
The scan tool does not show the respective normal
condition for item "FRONT ECU ACK" : Replace the
front-ECU. Verify that the windshield washer works
normally.
STEP 4. Check windshield washer motor connector A-33
for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is windshield washer motor connector A-33 in good
condition?
YES : Go to Step 5.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the windshield washer works
normally.
ITEM NO.
ITEM NAME
NORMAL
CONDITION
ITEM 09
FRONT
WASH.SW
ON
ITEM 70
FRONT ECU ACK NORMAL ACK or
HI-BEAM ACK
AC309091
MB991911
MB991827
MB991824
AB
MB991806
MB991862
DATA LINK
CONNECTOR
(16-PIN)
DATA LINK
CONNECTOR
(13-PIN)
AC205145AE
CONNECTOR: A-33
HARNESS SIDE
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-260
STEP 5. Check the windshield washer motor.
(1) Disconnect windshield washer motor connector A-33, and
check at windshield washer motor connector side.
(2) Fill the windshield washer tank with washer fluid.
(3) Connect windshield washer motor connector terminal 1 to
the positive battery terminal, and terminal 2 to the negative
battery terminal, respectively. Washer fluid should spray
out.
Q: Does the windshield washer motor operate normally?
YES : Go to Step 6.
NO : Replace the windshield washer motor. Verify that the
windshield washer works normally.
STEP 6. Check the ground circuit to the windshield washer
motor. Test at connector A-33.
(1) Disconnect windshield washer motor connector A-33 and
measure the resistance available at the wiring harness side
of the connector.
(2) Measure the resistance value between terminal 2 and
ground.
• The resistance should equal 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 8.
NO : Go to Step 7.
AC205145AE
CONNECTOR: A-33
HARNESS SIDE
AC309228AB
AC205145AE
CONNECTOR: A-33
HARNESS SIDE
AC209364KQ
CONNECTOR A-33
(HARNESS SIDE)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст