Mitsubishi Montero (2004+). Manual — part 815
INPUT SIGNAL PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-517
NOTE: Also check joint connector D-01, junction block connec-
tors D-208, D-212 and intermediate connector E-11 for loose,
corroded, or damaged terminals, or terminals pushed back in
the connector. If joint connector D-01, junction block connector
D-208, D-212 or intermediate connector E-11 is damaged,
Repair or replace the damaged component(s) as described in
GROUP 00E, Harness Connector Inspection
Q: Is the wiring harness between transmission range
switch connector C-04 (terminal 7) and the ignition
switch (IG1) in good condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. If the rear
wiper operates normally, it indicates that a correct "R"
position signal is sent from the transmission range
switch.
AC204170
CONNECTOR: D-01
AB
9 10
8
6 7
31 32
30
29
18 19 20 21
5
4
2
1
3
27
26
24
23
25
12 13 14 15 16 17
28
11
22
33
AC204191
CONNECTORS : D-208, D-212
D-208
AD
HARNESS SIDE
HARNESS SIDE
D-212
D-208
D-212
1
2
3
5
6
4
7 6 5
2 1
9 8
11 10
4 3
AC204176
CONNECTOR: E-11
AB
3
10
16
9
7 8
6
1
4
2
5
11
14
1213
15
INPUT SIGNAL PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-518
STEP 5. Check ETACS-ECU connector D-224 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Are ETACS-ECU connector D-224 in good condition?
YES : Go to Step 6.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. If the rear wiper operates normally, it
indicates that a correct "R" position signal is sent from
the transmission range switch.
STEP 6. Check the wiring harness between transmission
range switch connector C-04 (terminal 8) and ETACS-ECU
connector D-224 (terminal 35).
AC204174
CONNECTOR : D-224
AD
D-224(B)
D-224(B)
HARNESS SIDE
21
23
24
22
32
3433
31
26
27
28
3029
38
39
40
36
37
25
35
AC204395
CONNECTOR : C-04
HARNESS
SIDE
C-04(B)
C-04(B)
AB
1
6
3
8
4
9
5
10
7
2
AC204174
CONNECTOR : D-224
AD
D-224(B)
D-224(B)
HARNESS SIDE
21
23
24
22
32
3433
31
26
27
28
3029
38
39
40
36
37
25
35
INPUT SIGNAL PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-519
NOTE: Also check joint connector D-116, intermediate connec-
tors E-111 and E-114 for loose, corroded, or damaged termi-
nals, or terminals pushed back in the connector. If joint
connector D-116, intermediate connector E-111 or E-114 is
damaged, Repair or replace the damaged component(s) as
described in GROUP 00E, Harness Connector Inspection
.
Q: Is the wiring harness between transmission range
switch connector C-04 (terminal 8) and ETACS-ECU
connector D-224 (terminal 35) in good condition?
YES : Replace the ETACS-ECU. If the rear wiper operates
normally, it indicates that a correct "R" position signal
is sent from the transmission range switch.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. If the rear
wiper operates normally, it indicates that a correct "R"
position signal is sent from the transmission range
switch.
AC204171
CONNECTOR : D-116
AD
9 10
8
6 7
31 32
30
29
18 19 20 21
5
4
2
1
3
27
26
24
23
25
12 13 14 15 16 17
28
11
22
33
AC204194
CONNECTORS : E-111, E-114
E-111
AB
E-114
E-111
E-114
10
9
31
30
20 21
7
6
28
17 18
8
19
29
4
3
25 26
14 15
1
23
12
2
13
24
5
16
27
11
22
32
10
9
31
30
20 21
7
6
28
17 18
8
19
29
4
3
25 26
14 15
1
23
12
2
13
24
5
16
27
11
22
32
INPUT SIGNAL PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-520
INSPECTION PROCEDURE O-5: ETACS-ECU does not receive any signal from the driver's or the front
passenger's door switch.
Front Door Switches Input Circuit
AC204170
CONNECTORS: D-01, D-125
D-125
D-01
BY
AC204171
CONNECTOR : D-111
AG
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст