Mitsubishi Montero (2004+). Manual — part 734
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-193
STEP 38. Check at rear power window sub-switch (RH)
connector H-19 in order to check the ground circuit to the
rear power window sub-switch (RH).
(1) Disconnect rear power window sub-switch (RH) connector
H-19, and measure at the harness side.
(2) Measure the resistance value between terminal 5 and
ground.
• The resistance should measure 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 40.
NO : Go to Step 39.
STEP 39. Check the harness wiring between power
window main switch connector H-05 (terminal 2) and rear
power window sub-switch (RH) connector H-19 (terminal
5).
AC000316 AE
H-19
CONNECTOR: H-19
REAR DOOR<RH>
(HARNESS SIDE)
H-19
AC204323
1
2
3
4
5
6
AF
CONNECTOR H-19
(HARNESS SIDE)
AC203774
CONNECTOR: H-05
AF
DRIVER'S DOOR
H-05
H-05
(HARNESS SIDE)
AC000316 AE
H-19
CONNECTOR: H-19
REAR DOOR<RH>
(HARNESS SIDE)
H-19
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-194
NOTE: Also check intermediate connectors D-25, D-111 and
F-23. If intermediate connector D-25, D-111 or F-23 is dam-
aged, repair or replace the damaged component(s) as
described in GROUP 00E, Harness Connector Inspection
.
AC203859 AC
CONNECTOR: D-25
D-25
D-25
AC203860AC
D-111
CONNECTOR: D-111
D-111
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-195
Q: Is the harness wiring between power window main
switch connector H-05 (terminal 2) and rear power
window sub-switch (RH) connector H-19 (terminal 5) in
good condition?
YES : Replace the power window main switch. Verify that
the rear power window sub-switch (RH) should now
work normally.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the rear power window sub-switch (RH) should now
work normally.
STEP 40. Check at rear power window sub-switch (RH)
connector H-19 in order to check the ground circuit to the
rear power window sub-switch (RH).
(1) Disconnect rear power window sub-switch (RH) connector
H-19, and measure at the harness side.
(2) Measure the resistance value between terminal 2 and
ground.
• The resistance should measure 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 42.
NO : Go to Step 41.
AC204484
AC
CONNECTOR: F-23
F-23
F-23
AC000316 AE
H-19
CONNECTOR: H-19
REAR DOOR<RH>
(HARNESS SIDE)
H-19
AC204323
1
2
3
4
5
6
AG
CONNECTOR H-19
(HARNESS SIDE)
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-196
STEP 41. Check the harness wiring between power
window main switch connector H-05 (terminal 9) and rear
power window sub-switch (RH) connector H-19 (terminal
2).
AC203774
CONNECTOR: H-05
AF
DRIVER'S DOOR
H-05
H-05
(HARNESS SIDE)
AC000316 AE
H-19
CONNECTOR: H-19
REAR DOOR<RH>
(HARNESS SIDE)
H-19
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст