Mitsubishi Montero (2004+). Manual — part 768
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-329
NOTE: Also check intermediate connector F-10 for loose, cor-
roded, or damaged terminals, or terminals pushed back in the
connector. If intermediate connector F-10 is damaged, repair or
replace the damaged component(s) as described in GROUP
00E, Harness Connector Inspection
Q: Is the wiring harness between rear light (LH) connector
G-16 (terminal 3) and ground in good condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the taillights illuminate normally.
STEP 26. Check the taillight bulb (LH).
(1) Remove the taillight bulb (LH).
(2) Verify that the taillight bulb (LH) is not damaged or burned
out.
Q: Is the taillight bulb (LH) in good condition?
YES : Go to Step 27.
NO : Replace the taillight bulb (LH). Verify that the taillights
(LH) illuminates normally.
STEP 27. Check rear light (LH) connector G-16 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is rear light (LH) connector G-16 in good condition?
YES : Go to Step 28.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the taillights (LH) illuminates
normally.
AC204178
CONNECTOR : F-10
AD
F-10(GR)
F-10(GR)
3
1
2
4
5
6
AC204179
CONNECTOR : G-16
AH
HARNESS SIDE
G-16(B)
G-16(B)
3
4
2
1
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-330
STEP 28. Check the ground circuit to the taillight (LH). Test
at rear light (LH) connector G-16.
(1) Disconnect rear light (LH) connector G-16 and measure the
resistance available at the wiring harness side of the
connector.
(2) Measure the resistance value between terminal 3 and
ground.
• The resistance should equal 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 30.
NO : Go to Step 29.
STEP 29. Check the wiring harness between rear light (LH)
connector G-16 (terminal 3) and ground.
NOTE: Also check intermediate connector F-10 for loose, cor-
roded, or damaged terminals, or terminals pushed back in the
connector. If intermediate connector F-10 is damaged, repair or
replace the damaged component(s) as described in GROUP
00E, Harness Connector Inspection
Q: Is the wiring harness between rear light (LH) connector
G-16 (terminal 3) and ground in good condition?
YES : Replace the rear combination light socket (LH). Verify
that the taillight (LH) illuminates normally.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the taillights (LH) illuminates normally.
AC204179
CONNECTOR : G-16
AH
HARNESS SIDE
G-16(B)
G-16(B)
3
4
2
1
4
1
2
3
AC100265AB
CONNECTOR G-16
(HARNESS SIDE)
AC204179
CONNECTOR : G-16
AH
HARNESS SIDE
G-16(B)
G-16(B)
3
4
2
1
AC204178
CONNECTOR : F-10
AD
F-10(GR)
F-10(GR)
3
1
2
4
5
6
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-331
STEP 30. Check front-ECU connector A-07X for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is front-ECU connector A-07X in good condition?
YES : Go to Step 31.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the taillights (LH) illuminates
normally.
STEP 31. Check the wiring harness between rear light (LH)
connector G-16 (terminal 1) and front-ECU connector
A-07X (terminal 8).
AC204183
CONNECTOR : A-07X
AB
2 1
3
4
6
7
8
9
5
11 10
RELAY BOX SIDE
AC204183
CONNECTOR : A-07X
AB
2 1
3
4
6
7
8
9
5
11 10
RELAY BOX SIDE
AC204179
CONNECTOR : G-16
AH
HARNESS SIDE
G-16(B)
G-16(B)
3
4
2
1
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-332
NOTE: Also check intermediate connectors D-28, D-111 and
F-10 for loose, corroded, or damaged terminals, or terminals
pushed back in the connector. If intermediate connector D-28,
D-111 or F-10 is damaged, repair or replace the damaged com-
ponent(s) as described in GROUP 00E, Harness Connector
Inspection
.
Q: Is the wiring harness between rear light (LH) connector
G-16 (terminal 1) and front-ECU connector A-07X
(terminal 8) in good condition?
YES : Replace the rear combination light socket (LH). Verify
that the taillights (LH) illuminates normally.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the taillights (LH) illuminates normally.
STEP 32. Check the taillight bulb (RH).
(1) Remove the taillight bulb (RH).
(2) Verify that the taillight bulb (RH) is not damaged or burned
out.
Q: Is the taillight bulb (RH) in good condition?
YES : Go to Step 33.
NO : Replace the taillight bulb (RH). Verify that the taillight
(RH) illuminates normally.
AC204170
CONNECTOR : D-28
AI
2 3
27
32
28
33
16
15
4 5
19
18
29
17
34
7 8
35
22
21
9 10
30
36
31
37
25
24
23
6
20
1
14
26
11
13
12
38
AC204171
CONNECTOR : D-111
BH
9
8
6 7
5
3 4
20
32
21
33
43
17 18
30
41
16
29
28
39 40
13
25
12
24
35 36
14
26
37
15
27
38
19
31
42
1
10
22
2
11
23
34
AC204178
CONNECTOR : F-10
AD
F-10(GR)
F-10(GR)
3
1
2
4
5
6
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст