Mitsubishi Montero (2004+). Manual — part 892
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-143
STEP 28. Check the transmission range switch.
Measure the resistance between the terminals for each trans-
mission range as indicated in the table below.
Q: Is the measured resistance less than 2 ohms for each
transmission range?
YES : Go to Step 29.
NO : Replace the transmission range switch. Refer to
GROUP 23B, Transmission
STEP 29. Check transmission range switch connector C-04
for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is the connector in good condition?
YES : Go to Step 30.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
TRANSMISSION
RANGE
TERMINAL
CONNECTION OF
TESTER
SPECIFIED
CONDITION
P
1
− 7
Less than 2 ohms.
R
7
− 8
N
2
− 7
D
3
− 7
ACX01187AD
P
R
N
D
AC204395
CONNECTOR : C-04
AF
C-04 (B)
4
9
5
10
3
8
2
7
6
1
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-144
STEP 30. Measure the transmission range switch output
voltage at PCM connector D-134 by backprobing.
(1) Do not disconnect connector D-134.
(2) Turn the ignition switch to the "ON" position.
(3) Move the selector lever to the "D" position.
(4) Measure the voltage between terminal 76 and ground by
backprobing.
• The voltage should measure battery positive voltage.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage battery positive voltage?
YES : Go to Step 13.
NO : Go to Step 31.
AC204681AC
CONNECTOR: D-134
D-134 (GR)
61 62
63 64
65 66 67 68 69 70 71 72 73
82
89
81
88
80
79
78
77
87
86
85
76
75
74
84
83
AC204918 BM
D-134 HARNESS CONNECTOR :
HARNESS SIDE
76
85
65
72
71
73
82
75
81
74
63 64
66
70
69
68
67
78
87
79
88 89
80
77
86
62
61
83 84
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-145
STEP 31. Check PCM connector D-134 and intermediate
connector E-114 for loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 32.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC204681AC
CONNECTOR: D-134
D-134 (GR)
61 62
63 64
65 66 67 68 69 70 71 72 73
82
89
81
88
80
79
78
77
87
86
85
76
75
74
84
83
AC204176
CONNECTOR : E-114
BD
38
28
16
33
22
10
31
19
7
1
18
30
29
17
5
6
21
20
32
8
2
9
25
13
3
24
23
3435
1112
27
26
3637
14
4
15
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-146
STEP 32. Check harness for open circuit or short circuit to
ground between transmission range switch connector
C-04 terminal 3 and PCM connector D-134 terminal 76.
Q: Is the harness wire in good condition?
YES : Go to Step 33.
NO : Repair or replace the harness wire.
AC204395
CONNECTOR : C-04
AF
C-04 (B)
4
9
5
10
3
8
2
7
6
1
AC204681AC
CONNECTOR: D-134
D-134 (GR)
61 62
63 64
65 66 67 68 69 70 71 72 73
82
89
81
88
80
79
78
77
87
86
85
76
75
74
84
83
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст