Mitsubishi Montero (2004+). Manual — part 364
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-943
STEP 3. Check the circuit at PCM connector D-134.
(1) Disconnect the connectors D-134 and measure at the
harness side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal No. 69 and ground.
• Voltage should be 1 volt or less when the A/C switch is
"OFF".
• Voltage should be battery positive voltage when the A/C
switch is "ON".
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the voltage normal?
YES : Replace the PCM. Then confirm that the malfunction
symptom is eliminated.
NO : Refer to GROUP 55, Diagnosis
− Introduction To
Heater, Air Conditioning And Ventilation Diagnosis
AK201166
61
62
63
64
65
66
67
68
69
70
71
76
77
78
79
85
86
87
80
72
73
74
75
81
82
83
84
88
89
CONNECTOR: D-134
AB
PCM
D-134(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
61
62
63
64
65
66
67
68
69
70
71
76
77
78
79
85
86
87
80
72
73
74
75
81
82
83
84
88
89
AK201388
D-134 HARNESS
CONNECTOR:
COMPONENT SIDE
AK201388AB
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-944
INSPECTION PROCEDURE 33: Accelerator Pedal Position Switch
.
CIRCUIT OPERATION
• A 5-volt voltage is applied on the accelerator
pedal position switch output terminal (terminal
No. 4) from the PCM (terminal No. 38) via the
resistor in the PCM.
• The ground terminal (terminal No.5) is grounded
with PCM (terminal No.96).
.
YELLO
W
-BLA
CK
BLA
CK
AK201165
ACCELERATOR PEDAL
POSITION
SWITCH (BUILT INTO
ACCELERATOR
PEDAL
POSITION SENSOR)
POWERTRAIN CONTROL MODULE(PCM)
5V
96
38
4
5
D-138
(MU802073)
31
35363738394041 42 43
444546474849
50 51
5253
545556
57 58
32
33 34
9192
939495
96979899
100
105
113114
115116117
118119120
106
107108109
110111112
101102103
104
D-133
(MU803803)
D-135
(MU803805)
Accelerator Pedal Position Switch Circuit
6 7 8
1 2 3 4 5
AK200944AC
CONNECTOR: D-138
ACCELERATOR
PEDAL
POSITION
SWITCH
D-138(GR)
AK201038AL
CONNECTORS: D-133, D-135
PCM
D-135(GR)
D-133(GR)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-945
COMMENT
• Accelerator pedal position switch turns OFF
when the amount of travel of the accelerator
pedal exceeds the prescribed value.
• PCM uses the signal that is input by the accelera-
tor pedal position switch for determining the
abnormal characteristics of the accelerator pedal
position sensor (sub).
.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are: )
• Accelerator pedal position switch failed.
• Open or shorted accelerator pedal position switch
circuit, or loose connector.
• PCM failed.
DIAGNOSIS
STEP 1. Check connector D-138 at accelerator pedal
position switch for damage.
Q: Is the connector in good condition?
YES : Go to Step 3.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then confirm that the
malfunction symptom is eliminated.
STEP 2. Check the accelerator pedal position switch.
(1) Disconnect the accelerator pedal position switch connector
D-138.
(2) Check for continuity between the accelerator pedal position
switch side connector terminal No. 4 and No. 5.
• There should be continuity when the accelerator pedal
is not depressed. (400 ohms or less)
• There should be continuity when the accelerator pedal
is depressed.
Q: Does continuity exist?
YES : Go to Step 3.
NO : Replace the accelerator pedal position sensor
.
After converting the accelerator pedal position sensor,
adjust the accelerator pedal position sensor
. Confirm that the malfunction symptom is
eliminated.
AK200945
3
4
5
1
2
8
6
7
AB
CONNECTOR: D-138
HARNESS
CONNECTOR:
COMPONENT SIDE
D-138(GR)
AK200945
3
4
5
1
2
8
6
7
AB
CONNECTOR: D-138
HARNESS
CONNECTOR:
COMPONENT SIDE
D-138(GR)
1 2 3 4 5 6 7 8
AK201309 AC
Equipment side
connector
ACCELERATOR PEDAL
POSITION SWITCH
ACCELERATOR
PEDAL
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-946
STEP 3. Measure the switch supply voltage at accelerator
pedal position switch connector D-138.
(1) Disconnect the accelerator pedal position switch connector
D-138.
(2) Measure the voltage between terminal No. 4 and ground.
• Voltage should be 4 volts or more.
Q: Is the voltage normal?
YES : Go to Step 6.
NO : Go to Step 4.
STEP 4. Check connector D-133 at PCM for damage.
Q: Is the connector in good condition?
YES : Go to Step 5.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Confirm that the
malfunction system is eliminated.
AK200945
3
4
5
1
2
8
6
7
AB
CONNECTOR: D-138
HARNESS
CONNECTOR:
COMPONENT SIDE
D-138(GR)
3
4
5
1
2
8
6
7
AK201398
D-138 HARNESS
CONNECTOR:
COMPONENT SIDE
AK201398AB
AK200939
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
52
53
54
55
56
57
58
50
51
AB
CONNECTOR: D-133
HARNESS CONNECTOR:
COMPONENT SIDE
PCM
D-133(GR)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст