Mitsubishi Montero (2004+). Manual — part 700
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-57
.
CIRCUIT OPERATION
• Power to the sunroof motor assembly is supplied
through fusible links (1) and (4).
• When the ignition switch (IG2) signal is on, the
sunroof motor assembly is ready to operate.
.
TECHNICAL DESCRIPTION (COMMENT)
The power supply circuit or the communication circuit
to the sunroof motor assembly or the sunroof motor
assembly may be defective.
.
TROUBLESHOOTING HINTS
• The sunroof motor assembly may be defective
• The wiring harness or connectors may have
loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991911: MUT-III Main Harness B
ACX02274
FUSIBLE LINK (1), (4)
AE
BATTERY
FUSIBLE LINK (4)
FUSIBLE LINK (1)
AC204170
CONNECTORS : D-01, D-02, D-26, D-28
D-01
BF
D-28
D-02
D-26
AC204173
CONNECTORS : D-207, D-208, D-210, D-211
D-207
D-208
D-210
D-211(B)
AP
AC204174
CONNECTOR : D-224
D-224(B)
AG
AC204177
CONNECTORS : F-02, F-24
AJ
F-02
F-24
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-58
STEP 1. Check sunroof motor assembly connector F-02 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is sunroof motor assembly connector F-02 in good
condition?
YES : Go to Step 2.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. The system should communicate with the
sunroof motor assembly (sunroof-ECU) normally.
STEP 2. Check the fusible link (1) line of power supply
circuit to the sunroof motor assembly. Test at sunroof
motor assembly connector F-02.
(1) Disconnect sunroof motor assembly connector F-02 and
measure the voltage available at the wiring harness side of
the connector.
(2) Measure the voltage between terminal 3 and ground.
• The voltage should be approximately 12 volts (battery
positive voltage).
Q: Is the measured voltage approximately 12 volts (battery
positive voltage)?
YES : Go to Step 4.
NO : Go to Step 3.
AC204177
CONNECTOR : F-02
AB
HARNESS SIDE
1
5
2
7
8
6
3
4
10 9
F-02
AC204177
CONNECTOR : F-02
AB
HARNESS SIDE
1
5
2
7
8
6
3
4
10 9
F-02
AC204458
5
1
7
8
6
2
9
10
4
3
AB
CONNECTOR: F-02
(HARNESS SIDE)
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-59
STEP 3. Check the wiring harness between sunroof motor
assembly connector F-02 (terminal 3) and fusible link (1).
ACX02274
FUSIBLE LINK (1)
AE
BATTERY
AC204195
CONNECTORS : F-02, F-24
F-02
AB
HARNESS SIDE
F-24
F-02
F-24
1
5
2
7
8
6
3
4
10 9
6
2
5
4
3
1
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-60
NOTE: Also check junction block connectors D-207, D-221,
intermediate connectors D-26, D-28 and F-24 for loose, cor-
roded, or damaged terminals, or terminals pushed back in the
connector. If junction block connectors D-207, D-221, interme-
diate connectors D-26, D-28 or F-24 is damaged, repair or
replace the damaged component(s) as described in GROUP
00E, Harness Connector Inspection
Q: Is the wiring harness between sunroof motor assembly
connector F-02 (terminal 3) and fusible link (1) in good
condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. The system
should communicate with the sunroof motor assembly
(sunroof-ECU) normally.
AC204188
CONNECTORS : D-26, D-28
D-28
AH
D-26
D-28
D-26
2 3
27
32
28
33
16
15
4 5
19
18
29
17
34
7 8
35
22
21
9 10
30
36
31
37
25
24
23
6
20
1
14
26
11
13
12
38
2 3
1
7
6
12
11
8
13
5
4
9 10
AC204191
CONNECTORS : D-207, D-221
D-207
AB
HARNESS SIDE
HARNESS SIDE
D-221
D-207
D-221
3
1
4
6 5
7
8
2
1
2
3
4
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст